Laser Powder Bed Fusion of Ti-6Al-4V for Industrial Applications: Balancing Productivity and Mechanical Properties
2026 (English)Doctoral thesis, comprehensive summary (Other academic)Alternative title
Laserbaserad Pulverbäddsfusion av Ti-6Al-4V för industriella tillämpningar : avvägning mellan produktivitet och mekaniska egenskaper (Swedish)
Abstract [sv]
Additiv tillverkning (AM) möjliggör tillverkning av komplexa metalliskakomponenter direkt från digitala modeller, med minskat materialspilloch kortare väg från konstruktion till färdig komponent. Bland metallbaseradeAM tekniker har laserbaserad pulverbäddsfusion (PBF-LB) fåttett betydande industriellt genomslag. Samtidigt begränsas en bredareimplementering fortfarande av relativt låg produktivitet, kostnader koppladetill pulverråvaran och behovet av efterbearbetning för att uppnåerforderlig materialkvalitet.
Denna avhandling undersöker strategier för att öka produktiviteten vid PBF-LB-bearbetning av Ti-6Al-4V utan att försämra de mekaniska egenskaperna. En bred partikelstorleksfördelning på 15–90 μm kombinerades med en lagertjocklek på 70μm, och ett processfönster fastställdes genom att studera effekten av lasereffekt, skanningshastighet och spåravstånd på smältbad, konsolidering och defektbildning.
Resultaten visar att den bredare partikelstorleksfördelningen kan bearbetas framgångsrikt vid ökad lagertjocklek när processparametrarna anpassas på lämpligt sätt.
Två processstrategier studerades vidare: en med minimal porositet och en med hög produktivitet. Den högproduktiva strategin uppvisade lägre duktilitet och slagseghet i byggtillståndet till följd av bristande sammansmältning. Varmisostatisk pressning (HIP) användes därför både för konsolidering och mikrostrukturstyrning. HIP under β-transustemperaturen reducerade interna defekter och bibehöll en relativt fin mikrostruktur med hög duktilitet. HIP över β-transustemperaturen gav grövre tidigare β-korn och större α-kolonier, vilket förbättrade slagseghet och motstånd mot utmattningsspricktillväxt men minskade draghållfasthet och motstånd mot utmattningssprickinitiering.
Programmerbar laserstråleformning undersöktes även som ett verktyg för att påverka de termiska förhållandena under bearbetningen. Sammantaget visar avhandlingen att ökad PBF-LB-produktivitet kan uppnås genom en kombination av bredare partikelstorleksfördelning, ökad lagertjocklek, anpassade processparametrar och riktad efterbearbetning. Resultaten visar att produktivitet, defektpopulation, mikrostruktur och mekaniska egenskaper behöver betraktas som integrerade delar av samma tillverkningskedja.
Abstract [en]
Additive Manufacturing has transformed the production of metallic components by enabling complex geometries to be manufactured directly from digital models while reducing material waste and shortening the design-to-manufacture route. Among metal AM technologies, laser powder bed fusion (PBF-LB) has gained considerable industrial interest, particularly in the biomedical, automotive and aerospace sectors. Despite these advantages, wider industrial adoption remains constrained by relatively low build rates, feedstock optimisation costs and the need to consistently achieve the material quality required for structural applications by adding post processing.
This thesis investigates strategies for increasing the productivity of PBF-LB processing of Ti-6Al-4V while maintaining suitable mechanical properties. A wide powder particle size distribution of 15-90 μm was combined with an increased layer thickness of 70 μm, and a specific processing window was established by evaluating the effects of laser power, scanning speed and hatch distance on melt pool behaviour, consolidation and defect formation. The results show that the wider powder distribution can be successfully processed at increased layer thickness, provided that the process parameters are appropriately adapted.
Two representative processing strategies were subsequently investigated: a minimal porosity and a high productivity condition. The latter showed reduced ductility and impact toughness in the as-built condition due to lack-of-fusion defects. Hot Isostatic Pressing (HIP) was therefore investigated both as a consolidation method and as a means of tailoring the microstructure. Sub-β transus HIP effectively consolidated internal defects while retaining a comparatively refined microstructure and promoting high ductility. HIP above the β transus produced coarser prior-β grains and larger α colonies, improving impact toughness and fatigue crack growth resistance but reducing tensile strength and resistance to fatigue crack initiation. These findings show that the as-built condition affects not only defect formation but also the microstructure developed during subsequent HIP treatment.
Finally, programmable laser beam shaping was investigated as an additional tool to vary the thermal behaviour during processing.
Overall, the thesis demonstrates that increased PBF-LB productivity can be achieved through the combined use of wider powder particle size distributions, increased layer thickness, adapted process parameters and targeted post processing. The results highlight the need to consider productivity, defect content, microstructure and mechanical performance as an integrated manufacturing chain tailored to the requirements of the intended application.
Place, publisher, year, edition, pages
Trollhättan: University West , 2026. , p. 25
Series
PhD Thesis: University West ; 89
Keywords [en]
Powder Bed Fusion Laser Beam (PBF-LB), Ti-6Al-4V, Microstructure, Particle Size Distribution (PSD), Productivity Enhancement
Keywords [sv]
Pulverbädd additiv tillverkning (PBF-LB/M), Ti-6Al-4V, Mikrostruktur, Pulverpartikelstorleksfördelning, Produktivitetsförbättring
National Category
Manufacturing, Surface and Joining Technology
Identifiers
URN: urn:nbn:se:hv:diva-26329ISBN: 9789189969865 (print)ISBN: 9789189969858 (print)OAI: oai:DiVA.org:hv-26329DiVA, id: diva2:2109021
Public defence
2026-11-12, F210, Gustava Melins gata, Trollhättan, 09:00 (English)
Opponent
Supervisors
Note
Paper B and E are to be submitted and not included in the electronic thesis.
2026-10-202026-10-08
List of papers