The graphic abstract was missing from this article and it has been given in this correction. The original article has been corrected. © 2022, The Author(s) under exclusive licence to The Korean Institute of Metals and Materials.
The present endeavour is to augment mechanical attributes via friction stir processing (FSP) in hypereutectic aluminium-silicon castings by the means of microstructural modifications and defects reduction. Wherein, the study proceeds with mainly two approaches namely, alteration in tool revolution (TR) and the number of FSP passes. The prepared specimens were evaluated investigating volume fraction of porosities, microstructural characterizations and microhardness. Therefrom, the specimen with highest number of passes delivered most uniform properties resulting from the reduction in casting porosities and refined silicon particle uniform distribution throughout friction stir processed zone. This endeavour may be considered as a footstep towards more industrial readied material transformation.
Wire Arc Additive Manufacturing (WAAM) utilizes wire as the feedstock and welding arc as the heat source. While Solid Wires (SW) are common, exploration of tubular wires such as Metal Cored Wires (MCW) in Additive Manufacturing (AM) is limited. MCW offers flexibility for alloy design, but both SW and MCW can create silicon islands on welds, affecting mechanical properties and processability. This study uses Gas Metal Arc Welding (GMAW) in Cold Metal Transferred (CMT) mode to compare SW and MCW deposits with different gases. MCW shows more uniform penetration, potentially reducing lack of fusion in AM layers. A novel approach is then used to modify the MCW to minimize silicate formation, reducing islands on the surface. Comparative analysis shows a significant reduction and change in the location of silicates with modified MCW compared to standard, with mechanical properties in as-welded and after post-weld heat treatment (PWHT) remaining comparable to the standard wire.
Continuous cooling transformation (CCT) diagrams of base metals are common in welding. They can be built using physical or numerical simulations, each with advantages and limitations. However, those are not usual for weld metal, considering its variable composition due to the dilution of the weld into the base metal. Wire Arc Additive Manufacturing (WAAM) is a distinctive casein which the interest in materials comparable with weld composition raises attention to estimating their mechanical properties. Notwithstanding, this concept is still not used in WAAM. Therefore, the aim of this work was to address a methodology to raise MC-CCT (Multiple Cycle ContinuousCooling Transformation) diagrams for WAAM by combining physical and numerical simulations. A high-strength low-alloy steel (HSLA) feedstock (a combination of a wire and a shielding gas) was used as a case study. To keep CCT as representative as possible, the typical multiple thermal cycles for additive manufacturing thin walls were determined and replicated in physical simulations (Gleeble dilatometry). The start and end transformations were determined by the differential linear variation approach for each thermal cycle. Microstructure analyses and hardness were used to characterise the product after the multiple cycles. The same CCT diagram was raised by a commercial numerical simulation package to determine the shape of the transformation curves. A range of austenitic grain sizes was scanned for the curve position matching the experimental results. Combining the experimental data and numerically simulated curves made estimating the final CCT diagram possible.
Present work demonstrates high speed friction stir welding (HSFSW) of light weight battery trays assembly in electric vehicle (EV). Despite of solid-state and green nature of FSW, it suffers from the relatively low welding speed. With the help of suitable tool design and machine tool parameters, we successfully achieved defect-free welds at high welding speed of 4.0 and 4.5 m/min. Good quality welds are produced in 3 mm thick AA6063-T6 extruded aluminium alloy at such a high welding speeds by implementing violent material mixing i.e., higher tool rotation speeds (3500–4500 rpm) and plunge force (8.5–10.5 kN). The HSFSW cross-section registered curious hardness profile of ‘U’ shape. HSFSW resulted softening of weld stir zone (∼60 HV) along with HAZ (∼50 HV). The highest joint efficiency of 72 % was found for the weld produced at 4.0 m/min and 3500 rpm.
Present work aims to achieve high welding speed during friction stir welding of lightweight battery trays in the electric vehicle industry. This study reports high-speed friction stir welding (HSFSW) up to 4.0 m mi -1 in AA6063-T6 alloys. The defect-free HSFSW joints are produced by adopting aggressive material mixing, i.e. higher tool rotation and plunge force. HSFSW weld cross-section reported an unusual hardness profile of "U"shape instead of "W"shape in conventional FSW of AA6xxx alloys. HSFSW resulted softening of weld stir zone (~60HV) along with HAZ (~53HV) against the base material (BM) hardness of ~90HV. The HSFSW at 4.0 m min -1 obtained good joint strength of 71% of the BM. Microstructure evolutions across the fractured weld cross-section are discussed using EBSD analysis.
The present study focuses on developing lightweight assembly of two different aluminium alloys extruded and high pressure die cast (HPDC) for battery frame assembly in BEV. The goal is to produce defect-free welds in lap configuration with smooth surface finish. Stationary shoulder friction stir welding (SSFSW) was employed with welding speeds of 3–15 mm/s. EBSD analysis revealed two groups of grains in the stir zone (SZ) due to dynamic recrystallization. Moreover, the grain size of the SZ significantly decreased compared to both alloys. The cast alloy contains large iron particles, and that were broken by the rotating probe, and the stirred material consisted of fine dispersed precipitates. Tensile-shear test found the fracture location at the hook area near to cast, and a model representing fracture behavior is also discussed. With increasing welding speed from 3 to 5 mm/s, the tensile strength found ∼95 and ∼100 MPa, respectively without any significance difference in the fracture behavior and location. Overall, this study provides valuable insights such as materials mixing, grain refinement, and joint strength in dissimilar joining using SSFSW. The findings could be useful in developing optimized welding parameters and improving the overall quality and productivity of the SSFSW process for battery pack assembly in BEV.