Avoiding low austenite fractions and nitride formation are major challenges in laser welding of duplex stainless steels (DSS). The present research aims at investigating efficient means of promoting austenite formation during autogenous laser welding of DSS without sacrificing productivity. In this study, effects of shielding gas and laser reheating were investigated in welding of 1.5-mm-thick FDX 27 (UNS S82031) DSS. Four conditions were investigated: Ar-shielded welding, N2-shielded welding, Ar-shielded welding followed by Ar-shielded laser reheating, and N2-shielded welding followed by N2-shielded laser reheating. Optical microscopy, thermodynamic calculations, and Gleeble heat treatment were performed to study the evolution of microstructure and chemical composition. The austenite fraction was 22% for Ar-shielded and 39% for N2-shielded as-welded conditions. Interestingly, laser reheating did not significantly affect the austenite fraction for Ar shielding, while the austenite fraction increased to 57% for N2-shielding. The amount of nitrides was lower in N2-shielded samples compared to in Ar-shielded samples. The same trends were also observed in the heat-affected zone. The nitrogen content of weld metals, evaluated from calculated equilibrium phase diagrams and austenite fractions after Gleeble equilibrating heat treatments at 1100 °C, was 0.16% for N2-shielded and 0.11% for Ar-shielded welds, confirming the importance of nitrogen for promoting the austenite formation during welding and especially reheating. Finally, it is recommended that combining welding with pure nitrogen as shielding gas and a laser reheating pass can significantly improve austenite formation and reduce nitride formation in DSS laser welds. © 2020, The Author(s).

This paper aims at the phase identification and quantification in transformation induced plasticity duplex stainless steel (TDSS) base and weld metal containing ferrite, austenite, and martensite. Light optical microscopy (LOM) and electron backscatter diffraction (EBSD) analysis were employed to analyze phases. Samples were either mechanically or electrolytically polished to study the effect of the preparation technique. Mechanical polishing produced up to 26% strain-induced martensite. Electrolytic polishing with 150 g citric acid, 300 g distilled water, 600 mL H3PO4, and 450 mL H2SO4 resulted in martensite free surfaces, providing high-quality samples for EBSD analysis. Martensite identification was challenging both with LOM, due to the similar etching response of ferrite and martensite, and with EBSD, due to the similar lattice structures of ferrite and martensite. An optimized Beraha color etching procedure was developed that etched martensite distinctively. A novel step-by-step EBSD methodology was also introduced considering grain size and orientation, which successfully identified and quantified martensite as well as ferrite and austenite in the studied TDSS. Although here applied to a TDSS, the presented EBSD methodology is general and can, in combination with knowledge of the metallurgy of the specific material and with suitable adaption, be applied to a multitude of multiphase materials. It is also general in the sense that it can be used for base material and weld metals as well as additive manufactured materials.

Duplex stainless steel (DSS) blocks with dimensions of 150 × 70x30 mm3 were fabricated by Laser Metal Deposition with Wire (LMDw). Implementation of a programmable logic control system and the hot-wire technology provided a stable and consistent process producing high-quality and virtually defect-free deposits. Microstructure and mechanical properties were studied for as-deposited (AD) material and when heat-treated (HT) for 1 h at 1100 °C. The AD microstructure was inhomogeneous with highly ferritic areas with nitrides and austenitic regions with fine secondary austenite occurring in a periodic manner. Heat treatment produced a homogenized microstructure, free from nitrides and fine secondary austenite, with balanced ferrite and austenite fractions. Although some nitrogen was lost during LMDw, heat treatment or reheating by subsequent passes in AD allowed the formation of about 50% austenite. Mechanical properties fulfilled common requirements on strength and toughness in both as-deposited and heat-treated conditions achieving the highest strength in AD condition and best toughness and ductility in HT condition. Epitaxial ferrite growth, giving elongated grains along the build direction, resulted in somewhat higher toughness in both AD and HT conditions when cracks propagated perpendicular to the build direction. It was concluded that high-quality components can be produced by LMDw and that deposits can be used in either AD or HT conditions. The findings of this research provide valuable input for the fabrication of high-performance DSS AM components

A systematic four-stage methodology was developed and applied to the Laser Metal Deposition with Wire (LMDw) of a duplex stainless steel (DSS) cylinder > 20 kg. In the four stages, single-bead passes, a single-bead wall, a block, and finally a cylinder were produced. This stepwise approach allowed the development of LMDw process parameters and control systems while the volume of deposited material and the geometrical complexity of components increased. The as-deposited microstructure was inhomogeneous and repetitive, consisting of highly ferritic regions with nitrides and regions with high fractions of austenite. However, there were no cracks or lack of fusion defects; there were only some small pores, and strength and toughness were comparable to those of the corresponding steel grade. A heat treatment for 1 h at 1100 degrees (C) was performed to homogenize the microstructure, remove nitrides, and balance the ferrite and austenite fractions compensating for nitrogen loss occurring during LMDw. The heat treatment increased toughness and ductility and decreased strength, but these still matched steel properties. It was concluded that implementing a systematic methodology with a stepwise increase in the deposited volume and geometrical complexity is a cost-effective way of developing additive manufacturing procedures for the production of significantly sized metallic components.

Microstructure characteristics and pitting corrosion of a duplex stainless steel (DSS) manufactured by laser metal deposition with wire (LMDw) were studied. The layer-by-layer LMDw process resulted in a mixed microstructure of predominantly ferrite with 2% austenite and chromium-rich nitrides, and reheated regions with ~33% austenite. The high cooling rate of LMDw restricted the distribution of Cr, Mo, and Ni, in ferrite and austenite, while N diffuses from ferrite to austenite. Subsequent heat treatment at 1100 C for 1 h resulted in homogenized microstructure, dissolution of nitrides, and balanced ferrite/austenite ratio. It also led to the redistribution of Cr and Mo to ferrite, and Ni and N to austenite. At room temperature, cyclic potentiodynamic polarization measurements in 1.0 M NaCl solution showed no significant differences in corrosion resistance between the as-deposited and heat-treated samples, despite the differences in terms of ferrite to austenite ratio and elemental distribution. Critical pitting temperature (CPT) was the lowest (60 C) for the predominantly ferritic microstructure with finely dispersed chromium-rich nitrides; while reheated area with ~33% austenite in as-deposited condition achieved higher critical temperature comparable to what was obtained after heat treatment (73 and 68 C, respectively). At temperatures above the CPT, selective dissolution of the ferrite after deposition was observed due to depletion of N, while after heat treatment, austenite preferentially dissolved due to Cr and Mo concentrating in ferrite. In summary, results demonstrate how microstructural differences in terms of ferrite-to-austenite ratio, distribution of corrosion-resistant elements, and presence of nitrides affect corrosion resistance of LMDw DSS.