A growing understanding of wear behavior of various thermally sprayed ceramic–metallic matrix coatings has occurred over recent years. This has resulted from the continuous evolution in spraying methods as well as material feedstock, and the corresponding new aspects of the field that have been thoroughly explored. This paper aims to review recent developments in thermally sprayed tungsten carbide-based coatings, with specific emphasis on evaluating alternative binders, processing routes and tribological behavior of the coatings. A comprehensive evaluation of various compositions as binders for WC-based coatings, considering environmental concerns and market requirements has been carried out. The properties and performance of various potential alternatives for cobalt as a conventional binder for these coatings have been assessed. Moreover, different thermal spray methods have been reviewed, particularly highlighting the role of processing parameters, phase change and feedstock characteristics in the high-velocity oxy-fuel (HVOF) and high-velocity air fuel (HVAF) techniques. A comparison is made between HVAF and HVOF coatings in terms of their performance under different wear environments. Finally, various scenarios of material removal in HVAF and HVOF coatings, under various wear conditions, have also been reviewed.

Sliding wear performance of thermal spray WC-based coatings has been widely studied. However, there is no systematic investigation on the influence of test conditions on wear behaviour of these coatings. In order to have a good understanding of the effect of test parameters on sliding wear test performance of HVAF-sprayed WC–CoCr coatings, ball-on-disc tests were conducted under varying test conditions, including different angular velocities, loads and sliding distances. Under normal load of 20 N and sliding distance of 5 km (used as ‘reference’ conditions), it was shown that, despite changes in angular velocity (from 1333 rpm up to 2400 rpm), specific wear rate values experienced no major variation. No major change was observed in specific wear rate values even upon increasing the load from 20 N to 40 N and sliding distance from 5 km to 10 km, and no significant change was noted in the prevailing wear mechanism, either. Results suggest that no dramatic changes in applicable wear regime occur over the window of test parameters investigated. Consequently, the findings of this study inspire confidence in utilizing test conditions within the above range to rank different WC-based coatings.

In this study, effect of feedstock particle size and nozzle configuration on deposition, microstructural features, hardness and sliding wear behaviour of high velocity air fuel (HVAF)-sprayed WC-CoCr coatings was evaluated. Three different WC-CoCr powders with nominal particle sizes of 5/20 μm (fine), 5/30 μm (medium) and 15/45 μm (coarse) were sprayed employing a HVAF gun with four distinct DeLaval nozzle configurations involving different lengths and/or exit diameters. Microstructure, phase constitution and mechanical characteristics of the coatings were evaluated using SEM, EDS, XRD and micro indentation testing. Specific wear rate for all the samples was determined under sliding conditions and a comprehensive post wear analysis was conducted. X-ray diffraction analysis showed negligible decarburization in all the HVAF-sprayed coatings. It was shown that decrease in particle size of employed feedstock results in discernible changes in microstructural features of the coatings as well as considerable improvement in their performance. Also, notable changes in wear mechanisms were identified on reducing particle size from coarse to medium or fine. Fine and coarse feedstock powders were found to be sensitive to the type of nozzle used while no major difference was observed in coatings from powders with medium cut size sprayed with different nozzles.

The tribological performance of High Velocity Air-Fuel (HVAF) sprayed WC-based cermet coatings with binders containing no or very limited amount of cobalt was evaluated under dry sliding, erosion, and abrasion wear conditions. The wear and corrosion behaviors of WC-NiMoCrFeCo, WC-FeNiCrMoCu and WC-FeCrAl HVAF sprayed coatings were investigated and compared to standard WC-CoCr coatings as benchmark. Microstructure characterization along with XRD analysis was conducted on all powders as well as the corresponding coatings. Comprehensive post wear analysis was conducted on all coatings subjected to ball-on-disk, gas jet erosion and dry sand-rubber wheel abrasion tests. Moreover, all coatings were exposed to 3.5% (wt./vol.) NaCl aqueous solution to evaluate their corrosion performance through electrochemical testing. XRD results showed negligible phase transformation between the powders and the deposited coatings. The WC-NiMoCrFeCo coating exhibited the best sliding wear and electrochemical corrosion performance, with an average specific wear rate value of 3.1 x 10(-8) (mm(3).N-1.m(-1)) and a corrosion current density of 1.9 mu A/cm2. This coating also showed comparable abrasive wear resistance to the WC-CoCr coating. Under erosive wear conditions, too, the WC-FeNiCrMoCu and WC-FeCrAl coatings showed a comparable performance to the benchmark. Dominant wear mechanisms for the reference WC-CoCr coating, under sliding wear conditions, were abrasion (deep grooving) and surface fatigue (crack propagation and pitting). On the contrary, no pitting was observed in WC-NiMoCrFeCo and WC-FeCrAl coatings during the sliding wear test. No considerable difference was identified in the wear mechanisms of the different coatings under abrasion and erosion wear conditions. The results highlight the promise of some of the environment friendly binders studied to replace Co.

In this study, sliding and abrasion wear performance of WC-CoCr coatings deposited by high velocity air–fuel (HVAF) spraying with various thicknesses (i.e., 240, 150, 100, 50 and 30 µm), fabricated from fine feedstock powder (5–15 µm), were evaluated. The main aim was to investigate how thinner coatings (30 and 50 µm) perform compared to conventional thick coatings (> 100 µm), in an effort to address the supply and cost concerns associated with Co and W.

The feedstock powder and deposited coatings were characterized in terms of microstructure. The hardness of the thin and thick coatings was measured using Vickers hardness method from both cross section and top-surface. It was found that, regardless of the thickness, extremely dense coatings with very high hardness ( 1500 HV) can be deposited employing HVAF and fine feedstock powder. Thin and thick coatings were found to perform similarly under sliding wear with a normal load of 10 N or lower as well as under abrasion wear conditions which highlights the possibility of employing thinner coatings for a majority of the real applications.

The results suggest that peening effect does not have a considerable influence on the microstructure or performance of the deposited coatings. However, for sliding wear tests with a 20 N normal load, it was noticed that wear resistance of the coatings slightly declines with decreasing thickness of the coating beyond 150 µm. The main reason was identified to be the involvement of substrate effect when performing tests under severe Hertzian contact pressure.