Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
A detailed investigation of residual stresses after milling Inconel 718 using typical production parameters for assessment of affected depth
University West, Department of Engineering Science, Division of Subtractive and Additive Manufacturing. RISE IVF AB, Argongatan 30, Mölndal, 431 53, Sweden. (PTW)ORCID iD: 0000-0003-2991-2911
GKN Aerospace Sweden AB, Trollhättan, 461 81, Sweden.
RISE IVF AB, Argongatan 30, Mölndal, 431 53, Sweden.
University West, Department of Engineering Science, Division of Subtractive and Additive Manufacturing. (PTW)ORCID iD: 0000-0003-0976-9820
2020 (English)In: Materials Today Communications, ISSN 2352-4928, Vol. 24, article id 100958Article in journal (Refereed) Published
Abstract [en]

Production of superalloy gas turbine parts involves time consuming milling operations typically performed in a sequence from rough to finish milling. Rough milling using ceramic inserts allows high removal rates but causes severe sub-surface impact. A relatively large allowance is therefore left for subsequent cemented carbide milling. With increased knowledge of the affected depth it will be possible to reduce the machining allowance and increase efficiency of the manufacturing process. Milling Inconel 718 using typical production parameters has been investigated using new and worn ceramic and cemented carbide inserts. Residual stresses in a milled slot were measured by x-ray diffraction. Stresses were measured laterally across the slot and below the surface, to study the depth affected by milling. The most important result from this work is the development of a framework concerning how to evaluate the affected depth for a milling operation. The evaluation of a single milled slot shows great potential for determining the optimum allowance for machining. Our results show that the residual stresses are greatly affected by the ceramic and cemented carbide milling; both regarding depth as well as distribution across the milled slot. It has been shown that it is important to consider that the stresses across a milled slot are the highest in the center of the slot and gradually decrease toward the edges. Different inserts, ceramic and cemented carbide, and tool wear, alter how the stresses are distributed across the slot and the affected depth. © 2020 The Authors

Place, publisher, year, edition, pages
2020. Vol. 24, article id 100958
Keywords [en]
Carbide cutting tools; Carbide tools; Carbides; Milling (machining); Residual stresses, Allowance determination; Alloy 718; High speed milling; Material removal rate; Surface integrity, Cutting tools
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
URN: urn:nbn:se:hv:diva-14992DOI: 10.1016/j.mtcomm.2020.100958Scopus ID: 2-s2.0-85079036532OAI: oai:DiVA.org:hv-14992DiVA, id: diva2:1395753
Available from: 2020-02-24 Created: 2020-02-24 Last updated: 2020-02-24Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records BETA

Holmberg, JonasBeno, Tomas

Search in DiVA

By author/editor
Holmberg, JonasBeno, Tomas
By organisation
Division of Subtractive and Additive Manufacturing
In the same journal
Materials Today Communications
Manufacturing, Surface and Joining Technology

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 37 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf