Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Cutting temperatures during hard turning: Measurements and effects on white layer formation in AISI 52100
Chalmers University of Technology, Department of Materials and Manufacturing Technology.
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för industriell produktion. Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). (PTW)ORCID-id: 0000-0003-0976-9820
Lektronik, Ing.f:a, 424 49 Angered, Sweden .
Chalmers University of Technology, Department of Materials and Manufacturing Technology.
Visa övriga samt affilieringar
2014 (Engelska)Ingår i: Journal of Materials Processing Technology, ISSN 0924-0136, E-ISSN 1873-4774, Vol. 214, nr 6, s. 1293-1300Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

This paper concerns the temperature evolution during white layer formation induced by hard turning of martensitic and bainitic hardened AISI 52100 steel, as well as the effects of cutting temperatures and surface cooling rates on the microstructure and properties of the induced white layers. The cutting temperatures were measured using a high speed two-colour pyrometer, equipped with an optical fibre allowing for temperature measurements at the cutting edge. Depending on the machining conditions, white layers were shown to have formed both above and well below the parent austenitic transformation temperature, Ac1, of about 750 C. Thus at least two different mechanisms, phase transformation above the Ac1 (thermally) and severe plastic deformation below the Ac1 (mechanically), have been active during white layer formation. In the case of the predominantly thermally induced white layers, the cutting temperatures were above 900 C, while for the predominantly mechanically induced white layers the cutting temperatures were approximately 550 C. The surface cooling rates during hard turning were shown to be as high as 104-105 C/s for cutting speeds between 30 and 260 m/min independent of whether the studied microstructure was martensitic or bainitic. Adding the results from the cutting temperature measurements to previous results on the retained austenite contents and residual stresses of the white layers, it can be summarised that thermally induced white layers contain significantly higher amounts of retained austenite compared to the unaffected material and display high tensile residual stresses. On the contrary, in the case of white layers formed mainly due to severe plastic deformation, no retained austenite could be measured and the surface and subsurface residual stresses were compressive. © 2014 Elsevier B.V.

Ort, förlag, år, upplaga, sidor
2014. Vol. 214, nr 6, s. 1293-1300
Nyckelord [en]
Cutting temperatures, Hard turning, Intense plastic deformation, Phase transformation; Surface integrity, White layer
Nationell ämneskategori
Metallurgi och metalliska material
Forskningsämne
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-6216DOI: 10.1016/j.jmatprotec.2014.01.016ISI: 000334006600012Scopus ID: 2-s2.0-84894560151OAI: oai:DiVA.org:hv-6216DiVA, id: diva2:716038
Tillgänglig från: 2014-05-07 Skapad: 2014-05-07 Senast uppdaterad: 2019-11-18Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Beno, Tomas

Sök vidare i DiVA

Av författaren/redaktören
Beno, Tomas
Av organisationen
Avd för industriell produktionAvdelningen för avverkande och additativa tillverkningsprocesser (AAT)
I samma tidskrift
Journal of Materials Processing Technology
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 468 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf