Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Cutting temperatures during hard turning: Measurements and effects on white layer formation in AISI 52100
Chalmers University of Technology, Department of Materials and Manufacturing Technology.
University West, Department of Engineering Science, Division of Production Engineering. University West, Department of Engineering Science, Division of Subtractive and Additive Manufacturing. (PTW)ORCID iD: 0000-0003-0976-9820
Lektronik, Ing.f:a, 424 49 Angered, Sweden .
Chalmers University of Technology, Department of Materials and Manufacturing Technology.
Show others and affiliations
2014 (English)In: Journal of Materials Processing Technology, ISSN 0924-0136, E-ISSN 1873-4774, Vol. 214, no 6, p. 1293-1300Article in journal (Refereed) Published
Abstract [en]

This paper concerns the temperature evolution during white layer formation induced by hard turning of martensitic and bainitic hardened AISI 52100 steel, as well as the effects of cutting temperatures and surface cooling rates on the microstructure and properties of the induced white layers. The cutting temperatures were measured using a high speed two-colour pyrometer, equipped with an optical fibre allowing for temperature measurements at the cutting edge. Depending on the machining conditions, white layers were shown to have formed both above and well below the parent austenitic transformation temperature, Ac1, of about 750 C. Thus at least two different mechanisms, phase transformation above the Ac1 (thermally) and severe plastic deformation below the Ac1 (mechanically), have been active during white layer formation. In the case of the predominantly thermally induced white layers, the cutting temperatures were above 900 C, while for the predominantly mechanically induced white layers the cutting temperatures were approximately 550 C. The surface cooling rates during hard turning were shown to be as high as 104-105 C/s for cutting speeds between 30 and 260 m/min independent of whether the studied microstructure was martensitic or bainitic. Adding the results from the cutting temperature measurements to previous results on the retained austenite contents and residual stresses of the white layers, it can be summarised that thermally induced white layers contain significantly higher amounts of retained austenite compared to the unaffected material and display high tensile residual stresses. On the contrary, in the case of white layers formed mainly due to severe plastic deformation, no retained austenite could be measured and the surface and subsurface residual stresses were compressive. © 2014 Elsevier B.V.

Place, publisher, year, edition, pages
2014. Vol. 214, no 6, p. 1293-1300
Keywords [en]
Cutting temperatures, Hard turning, Intense plastic deformation, Phase transformation; Surface integrity, White layer
National Category
Metallurgy and Metallic Materials
Research subject
ENGINEERING, Manufacturing and materials engineering
Identifiers
URN: urn:nbn:se:hv:diva-6216DOI: 10.1016/j.jmatprotec.2014.01.016ISI: 000334006600012Scopus ID: 2-s2.0-84894560151OAI: oai:DiVA.org:hv-6216DiVA, id: diva2:716038
Available from: 2014-05-07 Created: 2014-05-07 Last updated: 2019-11-18Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records

Beno, Tomas

Search in DiVA

By author/editor
Beno, Tomas
By organisation
Division of Production EngineeringDivision of Subtractive and Additive Manufacturing
In the same journal
Journal of Materials Processing Technology
Metallurgy and Metallic Materials

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 550 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf