Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Milling Strategies for Thin-walled Components
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för industriell produktion. (PTW)
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för industriell produktion. (PTW)ORCID-id: 0000-0001-9331-7354
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för industriell produktion. Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). (PTW)ORCID-id: 0000-0003-0976-9820
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för industriell produktion. (PTW)ORCID-id: 0000-0003-1408-2249
2012 (engelsk)Inngår i: Advanced Materials Research, ISSN 1022-6680, E-ISSN 1662-8985, Vol. 498, s. 177-182Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Recent developments in the Aerospace industry have led to thin-walled, reduced-weight engine designs. Due to demands in manufacturing, production speeds and material removal rates (MRR) have increased. As component wall thickness gets thinner, the consequence oftentimes is an increase in chatter vibrations. This paper suggests that a correctly chosen tool-to-workpiece offset geometry may lead to a robust and chatter-free process. The results show the differences in force response for three geometries while varying the overhang of the workpiece. This is part of a concerted effort to develop a robust methodology for the prediction of chatter vibrations during milling operations of thin-walled Aerospace components. This paper outlines certain robust machining practices. It also analyzes the criticality of the choice of offset between tool and workpiece during milling setup as well as the effects that the entry and exit of cut have on system vibrations.

sted, utgiver, år, opplag, sider
2012. Vol. 498, s. 177-182
Emneord [en]
Thin-wall, Inconel 718, chatter, machining vibrations
HSV kategori
Forskningsprogram
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-4329DOI: 10.4028/www.scientific.net/AMR.498.177ISI: 000312878000030Scopus ID: 2-s2.0-84860254349OAI: oai:DiVA.org:hv-4329DiVA, id: diva2:527429
Konferanse
4th Manufacturing Engineering Society International Conference (MESIC),Cadiz, SPAIN, SEP 21-23, 2011
Tilgjengelig fra: 2012-05-31 Laget: 2012-05-21 Sist oppdatert: 2020-04-06bibliografisk kontrollert
Inngår i avhandling
1. Strategies for Reducing Vibrations during Milling of Thin-walled Components
Åpne denne publikasjonen i ny fane eller vindu >>Strategies for Reducing Vibrations during Milling of Thin-walled Components
2012 (engelsk)Licentiatavhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Factors such as environmental requirements and fuel efficiency have pushed aerospace industry to develop reduced-weight engine designs and thereby light-weight and thin-walled components. As component wall thickness gets thinner and the mechanical structures weaker, the structure becomes more sensitive for vibrations during milling operations. Demands on cost efficiency increase and new ways of improving milling operations must follow.

Historically, there have been two “schools” explaining vibrations in milling. One states that the entry angle in which the cutting insert hits the work piece is of greater importance than the exit angle. The other states that the way the cutter leaves the work piece is of greater importance than the cutter entry. In an effort to shed some light over this issue, a substantial amount of experiments were conducted. Evaluations were carried out using different tools, different tool-to-workpiece offset positions, and varying workpiece wall overhang. The resultant force, the force components, and system vibrations have been analyzed.

The first part of this work shows the differences in force behavior for three tool-to-workpiece geometries while varying the wall overhang of the workpiece. The second part studies the force behavior during the exit phase for five different tool-to-workpiece offset positions while the overhang is held constant. The workpiece alloy throughout this work is Inconel 718.

As a result of the project a spread sheet milling stability prediction model is developed and presented. It is based on available research in chatter theory and predicts the stability for a given set of variable input parameters.

sted, utgiver, år, opplag, sider
Stockholm: KTH Royal Institute of Technology, 2012. s. 96
Emneord
Milling, vibrations, chatter, stability, prediction, thin-wall, Inconel 718.
HSV kategori
Forskningsprogram
TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-4955 (URN)978-91-7501-322-0 (ISBN)
Presentation
2012-12-07, KTH Royal Institute of Technolgy, Brinellvägen 68, Stockholm, 10:00 (engelsk)
Opponent
Veileder
Tilgjengelig fra: 2012-12-28 Laget: 2012-12-27 Sist oppdatert: 2020-04-06bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopushttp://www.scientific.net

Person

Wanner, BertilEynian, MahdiBeno, TomasPejryd, Lars

Søk i DiVA

Av forfatter/redaktør
Wanner, BertilEynian, MahdiBeno, TomasPejryd, Lars
Av organisasjonen
I samme tidsskrift
Advanced Materials Research

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 333 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf