Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Balancing WAAM Production Costs and Wall Surface Quality through Parameter Selection: A Case Study of an Al-Mg5 Alloy Multilayer-Non-Oscillated Single Pass Wall
Center for Research and Development of Welding Processes, Federal University of Uberlandia, Uberlândia, Brazil.
Center for Research and Development of Welding Processes, Federal University of Uberlandia, Uberlândia, Brazil.
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för svetsteknologi (SV). Center for Research and Development of Welding Processes, Federal University of Uberlandia, Uberlândia, Brazil.ORCID-id: 0000-0002-1005-5895
2019 (Engelska)Ingår i: Journal of Manufacturing and Materials Processing, E-ISSN 2504-4494, Vol. 3, nr 2, s. 1-19Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The purpose of the study was to propose a strategy to assess the potential reduction of the production cost during wire+arc additive manufacturing (WAAM) based on the combination of wire feed speed (related to deposition rate) and travel speed (related to deposition time). A series of experiments, using a multilayer-non-oscillated single pass wall made of an Al-Mg alloy, was conducted. The quality of the wall was assessed through the lateral surface waviness and top layer undulation. The concepts of Surface Waviness and Buy-to-Apply indices were introduced. Initially, the range of travel speed (TS) that provided layers with acceptable quality was determined for a given wire feed speed (WFS), corresponding to a constant current. Then, the effect of the increase of production capacity of the process (though current raising, yet maintaining the ratio WFS/TS constant) on the wall quality for a given condition within the TS range was assessed. The results showed that the useful range of TS prevents too rough a waving surface below the lower limit and top surface undulation over the higher limit. However, inside the range, there is little quality variation for the case under study. Finally, simulations of deposition time were developed to demonstrate the weight of the TS on the final deposition time and wall quality as a function of a target wall width. This respective weight showed the existence of a complex and unpredictable, yet determined, power of a combination of TS, target wall geometry, and dead time between subsequent layers. It was verified to be possible to find optimized TS as a function of different target geometries. 

Ort, förlag, år, upplaga, sidor
MDPI, 2019. Vol. 3, nr 2, s. 1-19
Nyckelord [en]
WAAM; GMAW; CMT; aluminum; wall quality; production cost
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
TEKNIK, Produktions- och materialteknik; Produktionsteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-13793DOI: 10.3390/jmmp3020032OAI: oai:DiVA.org:hv-13793DiVA, id: diva2:1305340
Tillgänglig från: 2019-04-16 Skapad: 2019-04-16 Senast uppdaterad: 2019-04-17Bibliografiskt granskad

Open Access i DiVA

BalancingWAAM(4785 kB)20 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 4785 kBChecksumma SHA-512
514d1acf974967fd0ff9dd647e0504b46ffa84e54ee9f2b5f442f58b08c2e29bfda0c04ed1477bfc1afed0a1efa5ea08aba2d57c7f4514c7db25f8d7b64aa8a2
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltext

Personposter BETA

Scotti, Americo

Sök vidare i DiVA

Av författaren/redaktören
Scotti, Americo
Av organisationen
Avdelningen för svetsteknologi (SV)
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 20 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 75 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf