Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Evaluation of surface integrity after high energy machining with EDM, Laser Beam Machining and Abrasive Water Jet Machining of Alloy 718
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). Swerea-IVF AB, 431 22, Mölndal, Sweden. (PTW)ORCID-id: 0000-0003-2991-2911
GKN Aerospace Engine Systems AB, Trollhättan, Sweden.
Swerea IVF AB, Argongatan 30, 431 22 Mölndal, Sweden.
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). (PTW)
2019 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 100, nr 5-8, s. 1575-1591Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Development of future aero engine components based on new design strategies utilising topological optimisation and additive manufacturing has in the past years become a reality. This allows for designs that involve geometries of "free form" surfaces and material combinations that could be difficult to machine using conventional milling. Hence, alternative manufacturing routes using non-conventional high energy methods are interesting to explore. In this investigation, the three high energy machining methods abrasive water jet machining (AWJM), electrical discharge machining (EDM) and laser beam machining (LBM) have been compared in terms of surface integrity to the reference, a ball nosed end milled surface. The results showed great influence on the surface integrity from the different machining methods. It was concluded that AWJM resulted in the highest quality regarding surface integrity properties with compressive residual stresses in the surface region and a low surface roughness with texture from the abrasive erosion. Further, it was shown that EDM resulted in shallow tensile residual stresses in the surface and an isotropic surface texture with higher surface roughness. However, even though both methods could be considered as possible alternatives to conventional milling they require post processing. The reason is that the surfaces need to be cleaned from either abrasive medium from AWJM or recast layer from EDM. It was further concluded that LBM should not be considered as an alternative in this case due to the deep detrimental impact from the machining process.Keywords

Ort, förlag, år, upplaga, sidor
2019. Vol. 100, nr 5-8, s. 1575-1591
Nyckelord [en]
Non-conventional machining, EDM, Laser beam machining, Abrasive water jet machining, Surface integrity, Residual stress, EBSD, Topography
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Produktionsteknik; TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-12189DOI: 10.1007/s00170-018-2697-zOAI: oai:DiVA.org:hv-12189DiVA, id: diva2:1187094
Forskningsfinansiär
Vinnova, 2013-04666; 2015-06047
Anmärkning

First Online: 05 October 2018

Tillgänglig från: 2018-03-02 Skapad: 2018-03-02 Senast uppdaterad: 2019-06-11Bibliografiskt granskad
Ingår i avhandling
1. Surface integrity on post processed alloy 718 after nonconventional machining
Öppna denna publikation i ny flik eller fönster >>Surface integrity on post processed alloy 718 after nonconventional machining
2018 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

There is a strong industrial driving force to find alternative production technologies in order to make the production of aero engine components of superalloys even more efficient than it is today. Introducing new and nonconventional machining technologies allows taking a giant leap to increase the material removal rate and thereby drastically increase the productivity. However, the end result is to meet the requirements set for today's machined surfaces.The present work has been dedicated to improving the knowledge of how the non-conventional machining methods Abrasive Water Jet Machining, AWJM, Laser Beam Machining, LBM, and Electrical Discharge Machining, EDM, affect the surface integrity. The aim has been to understand how the surface integrity could be altered to an acceptable level. The results of this work have shown that both EDM and AWJM are two possible candidates but EDM is the better alternative; mainly due to the method's ability to machine complex geometries. It has further been shown that both methods require post processing in order to clean the surface and to improve the topography and for the case of EDM ageneration of compressive residual stresses are also needed.Three cold working post processes have been evaluated in order to attain this: shot peening, grit blasting and high pressure water jet cleaning, HPWJC. There sults showed that a combination of two post processes is required in order to reach the specified level of surface integrity in terms of cleaning and generating compressive residual stresses and low surface roughness. The method of high pressure water jet cleaning was the most effective method for removing the EDM wire residuals, and shot peening generated the highest compressive residual stresses as well as improved the surface topography.To summarise: the most promising production flow alternative using nonconventional machining would be EDM followed by post processing using HPWJC and shot peening.

Ort, förlag, år, upplaga, sidor
Trollhättan: University West, 2018. s. 92
Serie
Licentiate Thesis: University West ; 20
Nyckelord
Alloy 718, Non-conventional machining, post processing, surface integrity, Microstructure, Residual stress, Electron back scattering diffraction, Material removal rate
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Produktionsteknik; TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-12191 (URN)978-91-87531-72-9 (ISBN)978-91-87531-71-2 (ISBN)
Presentation
2018-03-07, C120, Högskolan Väst, Trollhättan, 10:15 (Engelska)
Opponent
Handledare
Tillgänglig från: 2018-03-07 Skapad: 2018-03-02

Open Access i DiVA

fulltext(10234 kB)68 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 10234 kBChecksumma SHA-512
bf3054bcc700e1e2db5ed76633eb1a62051df4c78fa53b016177bb21c1583f78fe9d81900b7bdf1a231d2600f5811e6da7b9260a4d9b2bcd5ea6a43e84ae83d6
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltext

Personposter BETA

Holmberg, JonasBeno, Tomas

Sök vidare i DiVA

Av författaren/redaktören
Holmberg, JonasBeno, Tomas
Av organisationen
Avdelningen för avverkande och additativa tillverkningsprocesser (AAT)
I samma tidskrift
The International Journal of Advanced Manufacturing Technology
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 68 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 161 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf