Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Energy and Cost Estimation of a Feature-based Machining Operation on HRSA
University West, Department of Engineering Science, Research Enviroment Production Technology West. GKN Aerospace Engine Systems AB, Trollhättan, Sweden. (PTW)ORCID iD: 0000-0002-2146-7916
University West, Department of Engineering Science, Division of Subtractive and Additive Manufacturing. (PTW)ORCID iD: 0000-0003-0976-9820
University West, Department of Engineering Science, Division of Industrial Engineering and Management, Electrical- and Mechanical Engineering. (PTW)
2017 (English)In: Procedia CIRP, ISSN 2212-8271, E-ISSN 2212-8271, Vol. 61, no Supplement C, p. 511-516Article in journal (Refereed) Published
Abstract [en]

Forward-looking manufacturing companies aim for sustainable production with low environmental footprint. This is true also for aerospace engine-makers, although their environmental impact mostly occurs during the use-phase of their products. Materials, such as Nickel alloys, are used for special applications where other materials will not withstand tough working conditions in terms of pressure and temperature. Heat Resistant Super Alloys are, however, considered difficult to machine and cutting tools will wear off rapidly. In this paper, a simple way to estimate the energy required, the cost and environmental footprint to produce a work piece using standard engineering software is presented. The results show that for a hypothetical 3 tonne work piece, Inconel 718 will be considerably cheaper and require less water but will require more energy, and has considerably larger CO2 footprint than Waspaloy.

Place, publisher, year, edition, pages
2017. Vol. 61, no Supplement C, p. 511-516
Keywords [en]
Energy use, sustainable consumption and production, production cost, environmental footprint, HRSA, feature based machining
National Category
Manufacturing, Surface and Joining Technology
Research subject
ENGINEERING, Manufacturing and materials engineering; Production Technology
Identifiers
URN: urn:nbn:se:hv:diva-11573DOI: 10.1016/j.procir.2016.11.141ISI: 000404511900089Scopus ID: 2-s2.0-85020019067OAI: oai:DiVA.org:hv-11573DiVA, id: diva2:1142645
Conference
24th CIRP Conference on Life Cycle Engineering (CIRP LCE), Kamakura, JAPAN, MAR 08-10, 2017
Funder
Knowledge Foundation
Note

Available from: 2017-09-19 Created: 2017-09-19 Last updated: 2020-02-06Bibliographically approved
In thesis
1. On cutting tool resource management
Open this publication in new window or tab >>On cutting tool resource management
2018 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The search for increased productivity and cost reduction in machining can be interpreted as desire to increase the Material Removal Rate, , and maximize the cutting tool utilization. The CNC process is complex and involves numerous constraints and parameters; ranging from tolerances to machinability. A well-managed preparation process creates the foundation for achieving a reduction in manufacturing errors and machining time. Along the preparation process of the NC-program, two different studies have been performed and are presented in this thesis. One study examined the CAM programming process from the Lean perspective. The other study includes an evaluation of how the cutting tools are used in terms of and tool utilization. Two distinct combinations of cutting data might provide the same . However, the tool life and machining cost can be different. Therefore, selection of appropriate cutting parameters that best meet all these objectives is challenging. An algorithm for analysis and efficient selection of cutting data for maximal , maximal tool utilization and minimal machining cost has been developed and is presented in this work. The presented algorithm shortens the time dedicated to the optimized cutting data selection and the needed iterations along the program development. Furthermore, the objectives that need to be considered during the estimation of the manufacturing processes sustainability have been identified. In addition, this thesis also includes a theoretical study to estimate energy use, CO2-footprint and water consumption during the manufacture of a workpiece, which can be invaluable for companies in their search for sustainability of their manufacturing processes.

Place, publisher, year, edition, pages
Trollhättan: University West, 2018. p. 108
Series
PhD Thesis: University West ; 16
Keywords
CAM programming; Cutting data; Lean; Manufacturing; Material Removal Rate; Optimization; Tool life; Tool utilization; Tool wear; Sustainability
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
urn:nbn:se:hv:diva-12240 (URN)978-91-87531-82-8 (ISBN)978-91-87531-81-1 (ISBN)
Public defence
2018-05-08, F104, University West, Trollhättan, 10:15 (English)
Opponent
Supervisors
Available from: 2018-04-12 Created: 2018-04-06 Last updated: 2018-10-26Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records

Bonilla Hernández, Ana EstherBeno, TomasFredriksson, Claes

Search in DiVA

By author/editor
Bonilla Hernández, Ana EstherBeno, TomasFredriksson, Claes
By organisation
Research Enviroment Production Technology WestDivision of Subtractive and Additive ManufacturingDivision of Industrial Engineering and Management, Electrical- and Mechanical Engineering
In the same journal
Procedia CIRP
Manufacturing, Surface and Joining Technology

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 593 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf