Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of pressure and temperature on densification, microstructure and mechanical properties of spark plasma sintered silicon carbide processed with β-silicon carbide nanopowder and sintering additives
International Advanced Research Centre for Powder Metallurgy and New Materials, Balapur Post, Hyderabad, 500005 Telangana, India.
International Advanced Research Centre for Powder Metallurgy and New Materials, Balapur Post, Hyderabad, 500005 Telangana, India.
International Advanced Research Centre for Powder Metallurgy and New Materials, Balapur Post, Hyderabad, 500005 Telangana, India.
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, 721302 West Bengal, India.
Visa övriga samt affilieringar
2016 (Engelska)Ingår i: Ceramics International, ISSN 0272-8842, E-ISSN 1873-3956, Vol. 42, nr 3, s. 3836-3848Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The effects of applied pressure and temperature during spark plasma sintering (SPS) of additive-containing nanocrystalline silicon carbide on its densification, microstructure, and mechanical properties have been investigated. Both relative density and grain size are found to increase with temperature. Furthermore, with increase in pressure at constant temperature, the relative density improves significantly, whereas the grain size decreases. Reasonably high relative density (~96%) is achieved on carrying out SPS at 1300 °C under applied pressure of 75 MPa for 5 min, with a maximum of ~97.7% at 1500 °C under 50 MPa for 5 min. TEM studies have shown the presence of an amorphous phase at grain boundaries and triple points, which confirms the formation of liquid phase during sintering and its significant contribution to densification of SiC at relatively lower temperatures (≤1400 °C). The relative density decreases on raising the SPS temperature beyond 1500 °C, probably due to pores caused by vaporization of the liquid phase. Whereas β-SiC is observed in the microstructures for SPS carried out at temperatures ≤1500 °C, α-SiC evolves and its volume fraction increases with further increase in SPS temperatures. Both hardness and Young׳s modulus increase with increase in relative density, whereas indentation fracture toughness appears to be higher in case of two-phase microstructure containing α and β-SiC.

Ort, förlag, år, upplaga, sidor
2016. Vol. 42, nr 3, s. 3836-3848
Nyckelord [en]
C. Mechanical properties, D. SiC, SPS, Densification, Microstructure
Nationell ämneskategori
Metallurgi och metalliska material Keramteknik
Forskningsämne
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-10323DOI: 10.1016/j.ceramint.2015.11.048OAI: oai:DiVA.org:hv-10323DiVA, id: diva2:1057234
Tillgänglig från: 2016-12-16 Skapad: 2016-12-16 Senast uppdaterad: 2019-05-20Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Joshi, Shrikant

Sök vidare i DiVA

Av författaren/redaktören
Joshi, Shrikant
Av organisationen
Forskningsmiljön produktionsteknik(PTW)
I samma tidskrift
Ceramics International
Metallurgi och metalliska materialKeramteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 940 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf