Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Inductive measurement of narrow gaps for high precision welding of square butt joints
University West, Department of Engineering Science, Research Enviroment Production Technology West. (PTW)ORCID iD: 0000-0003-3697-1995
2016 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

A recent method in aero engine production is to fabricate components from smaller pieces, rather than machining them from large castings. This has made laser beam welding popular, offering high precision with low heat input and distortion, but also high productivity. At the same time, the demand for automation of production has increased, to ensure high quality and consistent results. In turn, the need for sensors to monitor and control the laser welding process is increasing. In laser beam welding without filler material, the gap between the parts to be joined must be narrow. Optical sensors are often used to measure the gap, but with precise machining, it may become so narrow that it is difficult to detect, with the risk of welding in the wrong position. This kind of problems can cause severe welding defects, where the parts are only partially joined without any visible indication. This thesis proposes the use of an inductive sensor with coils on either side of the gap. Inducing currents into the metal, such a sensor can detect even gaps that are not visible. The new feature of the proposal is based on using the complex response of each coil separately to measure the distance and height on both sides of the gap, rather than an imbalance from the absolute voltage of each coil related to gap position. This extra information allows measurement of gap width and misalignment as well as position, and decreases the influence from gap misalignment to the position measurement. The sensor needs to be calibrated with a certain gap width and height alignment. In real use,these will vary, causing the sensor to be less accurate. Using initial estimates ofthe gap parameters from the basic sensor, a model of the response can be used to estimate the measurement error of each coil, which in turn can be used for compensation to improve the measurement of the gap properties.The properties of the new method have been examined experimentally, using a precise traverse mechanism to record single coil responses in a working range around a variable dimension gap, and then using these responses to simulate a two coil probe. In most cases errors in the measurement of weld gap position and dimensions are within 0.1 mm.The probe is designed to be mounted close to the parts to be welded, and will work in a range of about 1 mm to each side and height above the plates. This is an improvement over previous inductive sensors, that needed to be guided to the mid of the gap by a servo mechanism.

Place, publisher, year, edition, pages
Trollhättan: University West , 2016. , p. 48
Series
Licentiate Thesis: University West ; 14
Keywords [en]
Eddy current, Seam tracking, Measurement, Laser beam welding
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
URN: urn:nbn:se:hv:diva-10150ISBN: 978-91-87531-45-3 (print)ISBN: 978-91-87531-44-6 (print)OAI: oai:DiVA.org:hv-10150DiVA, id: diva2:1047305
Presentation
2016-11-28, C118, Högskolan Väst, Trollhättan, 10:15
Supervisors
Available from: 2016-11-21 Created: 2016-11-17 Last updated: 2019-12-03Bibliographically approved
List of papers
1. A complex response inductive method for improved gap measurement in laser welding
Open this publication in new window or tab >>A complex response inductive method for improved gap measurement in laser welding
2017 (English)In: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 88, no 1-4, p. 175-184Article in journal (Refereed) Published
Abstract [en]

Laser welding needs precise measurement of weldgap position to avoid weld defects. Most often, optical measurement methods are used, but well-aligned narrow gaps canbe difficult to detect. An improved inductive method capable of detecting zero gaps in square butt joints is proposed. The new method uses two eddy current coils, one on each side of the gap, and measures the complex response of the individual coils, i.e. both the inductive and resistive response. By combining the coil responses, both the position and the geometry of the weld gap can be estimated. The method was experimentally investigated by traversing a single coil over an adjustable gap between two plates and combining the measured coil responses into a simulated two-coil probe. The gap was adjusted in both misalignment and gap width up to 0.4 mm. Comparing the results to known settings and positions shows that gap position is measured to within 0.1 mm, if the probe is within a working area of 1 mm from the gap in both position and height. Results from the new method were compared to simulations, from the same experimental data, of a previously reported method where the coils were electrically combined by wiring them together. The previous method can give accurate results but has a much smaller working area and depends on servo actuation to position the probe above the gap. The improved method gives better tolerance to varying misalignment and gap width, which is an advantage over previous inductive methods.

Keywords
Seam tracking, Inductive, Complex response, Zero-gap measurement, Laser beamwelding, Square butt joint
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
urn:nbn:se:hv:diva-10146 (URN)10.1007/s00170-016-8750-x (DOI)000392308400016 ()2-s2.0-84964330115 (Scopus ID)
Funder
Knowledge Foundation
Available from: 2016-11-17 Created: 2016-11-17 Last updated: 2022-11-08Bibliographically approved
2. Evaluation of non-contact methods for joint tracking in a laser beam welding application
Open this publication in new window or tab >>Evaluation of non-contact methods for joint tracking in a laser beam welding application
Show others...
2016 (English)In: The 7th International Swedish Production Symposium, Conference Proceedings: 25th – 27th of October 2016, Lund: Swedish Production Symposium , 2016, p. 1-6Conference paper, Published paper (Refereed)
Abstract [en]

The use of automated laser welding is a key enabler for resource efficient manufacturing in several industrial sectors. One disadvantage with laser welding is the narrow tolerance requirements in the joint fit-up. This is the main reason for the importance of joint tracking systems. This paper describes anevaluation of four non-contact measurement methods to measure the position, gap width and misalignment between superalloy plates. The evaluation was carried out for increased knowledge about the possibilities and limitations with the different methods. The methods are vision-, laser-line-,thermography- and inductive probe systems which are compared in an experimental setup representing a relevant industrial application. Vision is based on a CMOS camera, where the image information is used directly for the measurements. Laser-line is based on triangulation between a camera and a projected laserline. Thermography detects the heat increase in the gap width due to external heat excitation. Inductive probe uses two eddy current coils, and by a complex response method possibilities to narrow gap measurement is achieved. The results, evaluated by comparing the data from the different systems, clearly highlights possibilities and limitations with respective method and serves as a guide in the development of laser beam welding.

Place, publisher, year, edition, pages
Lund: Swedish Production Symposium, 2016
Keywords
Joint tracking, Gap width, Misalignment, Inductive coil, Thermography, Laser line, Vision sensor
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
urn:nbn:se:hv:diva-10147 (URN)
Conference
7th Swedish Production Symposium, Lund, Sweden, October 25-27, 2016
Note

Ingår i lic.uppsats

Available from: 2016-11-17 Created: 2016-11-17 Last updated: 2022-11-08Bibliographically approved
3. Model based compensation of systematic errors in an inductive gap measurement method
Open this publication in new window or tab >>Model based compensation of systematic errors in an inductive gap measurement method
2017 (English)In: Measurement : Journal of the International Measurement Confederation, ISSN 0263-2241, Vol. 105, p. 17-24Article in journal (Refereed) Published
Abstract [en]

This paper presents an improvement to a recently presented inductive gap measurement method, using a model to reduce systematic errors. Gap measurement is important in laser keyhole welding, where the laser beam and the resulting weld seam are very narrow, requiring high precision in alignment and gap preparation. The previously reported method for gap measurement uses one inductive coil on each side of the gap, each measuring distance to the gap and lift off above a plate, to estimate the position, width and alignment of the gap in a square butt joint. The method can detect zero width gap and shows position error less than 0.1 mm, but gap width and alignment measurement suffer from systematic errors. The improvement is based on a model that is designed to describe these systematic errors as functions of the gap dimensions. The model relies on observations of experimental data, and is calibrated to a small set of measurements. Using the model with the initial estimate of the gap dimensions to compensate the coil measurements, an improved estimate of the gap dimensions can be calculated. The errors in the compensated results are within 0.1 mm except for gap width, which still suffers from the effect of combined gap width and misalignment.

Place, publisher, year, edition, pages
Elsevier, 2017
Keywords
Seam tracking, inductive, complex response, zero gap, laser beam welding, error compensation
National Category
Manufacturing, Surface and Joining Technology
Research subject
Production Technology; ENGINEERING, Manufacturing and materials engineering
Identifiers
urn:nbn:se:hv:diva-10148 (URN)10.1016/j.measurement.2017.03.043 (DOI)000401378400003 ()2-s2.0-85017174867 (Scopus ID)
Funder
Knowledge Foundation
Note

Ingår i lic. uppsats

Available from: 2016-11-17 Created: 2016-11-17 Last updated: 2019-12-05Bibliographically approved

Open Access in DiVA

fulltext(6495 kB)934 downloads
File information
File name FULLTEXT01.pdfFile size 6495 kBChecksum SHA-512
025d8a3ef69b9d4c9f44e85e788d99dcac03755a8d02039069b4b207aeb28ece039d75d363f8485a1acc3f5d398494120fa9eda47efd65be91109f0c66c0137d
Type fulltextMimetype application/pdf

Authority records

Svenman, Edvard

Search in DiVA

By author/editor
Svenman, Edvard
By organisation
Research Enviroment Production Technology West
Manufacturing, Surface and Joining Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 934 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

isbn
urn-nbn

Altmetric score

isbn
urn-nbn
Total: 637 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf