Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Sliding and abrasive wear behaviour of HVOF- and HVAF-sprayed Cr3C2-NiCr hardmetal coatings
University of Modena and Reggio Emilia, Dipartimento di Ingegneria 'Enzo Ferrari', Via P. Vivarelli 10/1, Modena, MO, Italy .
Fraunhofer-Institut für Werkstoff- und Strahltechnik (IWS), Winterbergstr. 28, Dresden, Germany.
Fraunhofer-Institut für Werkstoff- und Strahltechnik (IWS), Winterbergstr. 28, Dresden, Germany.
Tampere University of Technology, Department of Materials Science, Korkeakoulunkatu 6, Tampere, Finland .
Visa övriga samt affilieringar
2016 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 358-359, s. 32-50Artikel i tidskrift (Refereegranskat) Published
Resurstyp
Text
Abstract [en]

This paper provides a comprehensive characterisation of HVOF- and HVAF-sprayed Cr3C2–25 wt.% NiCr hardmetal coatings. One commercial powder composition with two different particle size distributions was processed using five HVOF and HVAF thermal spray systems.All coatings contain less Cr3C2 than the feedstock powder, possibly due to the rebound of some Cr3C2-rich particles during high-velocity impact onto the substrate.Dry sand-rubber wheel abrasive wear testing causes both grooving and pull-out of splat fragments. Mass losses depend on inter- and intra-lamellar cohesion, being higher (≥70 mg after a wear distance of 5904 m) for the coatings deposited with the coarser feedstock powder or with one type of HVAF torch.Sliding wear at room temperature against alumina involves shallower abrasive grooving, small-scale delamination and carbide pull-outs, and it is controlled by intra-lamellar cohesion. The coatings obtained from the fine feedstock powder exhibit the lowest wear rates (≈5x10−6 mm3/(Nm)). At 400 °C, abrasive grooving dominates the sliding wear behaviour; wear rates increase by one order of magnitude but friction coefficients decrease from ≈0.7 to ≈0.5. The thermal expansion coefficient of the coatings (11.08x10−6 °C−1 in the 30–400 °C range) is sufficiently close to that of the steel substrate (14.23x10−6 °C−1) to avoid macro-cracking

Ort, förlag, år, upplaga, sidor
2016. Vol. 358-359, s. 32-50
Nyckelord [en]
Abrasion, Abrasives, Adhesion, Alumina, Carbides, Cermets, Coatings, Failure (mechanical), Feedstocks, Friction, Indentation, Particle size, Powder coatings, Rubber testing, Sprayed coatings, Thermal expansion, Wear of materials, Friction coefficients, High temperature, High-velocity impact, Sliding wear, Sliding wear behaviour, Thermal expansion coefficients, Thermal spray coatings, Three body abrasion, HVOF thermal spraying
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-9325DOI: 10.1016/j.wear.2016.03.034ISI: 000375844800005Scopus ID: 2-s2.0-84962802963OAI: oai:DiVA.org:hv-9325DiVA, id: diva2:922851
Tillgänglig från: 2016-04-25 Skapad: 2016-04-25 Senast uppdaterad: 2017-11-30Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Lyphout, ChristopheMarkocsan, NicolaieNylén, Per

Sök vidare i DiVA

Av författaren/redaktören
Lyphout, ChristopheMarkocsan, NicolaieNylén, Per
Av organisationen
Avd för industriell produktionForskningsmiljön produktionsteknik(PTW)
I samma tidskrift
Wear
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 347 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf