Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of detonation gun sprayed Cu-Ni-In coating on plain fatigue and fretting fatigue behaviour of Al-Mg-Si alloy
2006 (Engelska)Ingår i: Surface & Coatings Technology, ISSN 0257-8972, E-ISSN 1879-3347, Vol. 201, nr 3-4, s. 1548-1558Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Detonation gun spray technique was employed to coat Al-Mg-Si alloy (AA 6063) specimens with Cu-Ni-In powder. Coated samples were characterized with reference to the microstructure, porosity, residual stresses, microhardness and surface roughness. Plain fatigue (without fretting) and fretting fatigue tests were carried out at room temperature on uncoated and coated specimens. The detonation gun spray process resulted in a dense coating of almost uniform deposition with low porosity (0.3%) and good adhesion between the substrate and the coating. Under plain fatigue loading 40 mu m thick coated samples exhibited superior lives compared with uncoated and 100 mu m thick coated specimens due to the presence of higher surface compressive residual stress in the former. Delamination-induced failure resulted in inferior lives of 100 mu m thick coated specimens. Under fretting fatigue deformation 40 mu m thick coated specimens exhibited superior lives compared with 100 mu m thick coated samples owing to higher compressive residual stress at the surface and better interfacial adhesion. At 120 MPa stress level 40 pm thick coated specimens exhibited superior fretting fatigue life compared with uncoated sample and at stress levels above 120 MPa the converse was true. This was attributed to interface cracking at higher stress levels. (c) 2006 Elsevier B.V. All rights reserved.

Ort, förlag, år, upplaga, sidor
2006. Vol. 201, nr 3-4, s. 1548-1558
Nyckelord [en]
fretting fatigue, Cu-Ni-In, detonation gun, residual stress, Al-Mg-Si, alloy, SURFACE TREATMENTS, STRENGTH, STEEL, PALLIATIVES, Materials Science, Coatings & Films, Physics, Applied
Identifikatorer
URN: urn:nbn:se:hv:diva-8493OAI: oai:DiVA.org:hv-8493DiVA, id: diva2:860110
Tillgänglig från: 2015-10-10 Skapad: 2015-10-08 Senast uppdaterad: 2017-12-01Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Person

Joshi, S. V.

Sök vidare i DiVA

Av författaren/redaktören
Joshi, S. V.
I samma tidskrift
Surface & Coatings Technology

Sök vidare utanför DiVA

GoogleGoogle Scholar

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 111 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf