Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Development of bondcoats for high lifetime suspension plasma sprayed thermal barrier coatings
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). (PTW)ORCID-id: 0000-0002-4201-668X
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). (PTW)ORCID-id: 0000-0002-9578-4076
Siemens Turbomachinery AB, Finspång, Sweden.
GKN Aerospace, Trollhättan, Sweden.
2019 (Engelska)Ingår i: Surface & Coatings Technology, ISSN 0257-8972, E-ISSN 1879-3347, Vol. 371, s. 366-377Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Fabrication of thermal barrier coatings (TBCs) by suspension plasma spraying (SPS) seems to be a promising alternative for the industry as SPS TBCs have the potential to provide lower thermal conductivity and longer lifetime than state-of-the-art allowing higher engine efficiency. Further improvements in lifetime of SPS TBCs and fundamental understanding of failure mechanisms in SPS TBCs are necessary for their widespread commercialisation. In this study, the influence of varying topcoat-bondcoat interface topography and bondcoat microstructure on lifetime was investigated. The objective of this work was to gain fundamental understanding of relationships between topcoat-bondcoat interface topography, bondcoat microstructure, and failure mechanisms in SPS TBCs. Seven sets of samples were produced in this study by keeping same bondcoat chemistry but varying feedstock particle size distributions and bondcoat spray processes. The topcoat chemistry and spray parameters were kept identical in all samples. Three-dimensional surface measurements along with scanning electron microscopy images were used to characterise bondcoat surface topography. The effect of varying interface topography and bondcoat microstructure on thermally grown oxide formation, stresses and lifetime was discussed. The results showed that varying bondcoat powder size distribution and spray process can have a significant effect on lifetime of SPS TBCs. Smoother bondcoats seemed to enhance the lifetime in case of SPS TBCs in case of same bondcoat chemistry and similar bondcoat microstructures. When considering the samples investigated in this study, samples with high velocity air-fuel (HVAF) bondcoats resulted in higher lifetime than other samples indicating that HVAF could be a suitable process for bondcoat deposition in SPS TBCs. © 2018 Elsevier B.V.

Ort, förlag, år, upplaga, sidor
2019. Vol. 371, s. 366-377
Nyckelord [en]
Air, Failure (mechanical), Microstructure, Particle size, Plasma jets, Plasma spraying, Scanning electron microscopy, Size distribution, Sprayed coatings, Surface measurement, Surface topography, Thermal conductivity, Thermal spraying, Topography, Bond coats, Interface topography, Lifetime, Suspension plasma spraying, Thermal barrier coating (TBCs), Thermally grown oxide, Thermal barrier coatings
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-13178DOI: 10.1016/j.surfcoat.2018.11.013Scopus ID: 2-s2.0-85056458705OAI: oai:DiVA.org:hv-13178DiVA, id: diva2:1267619
Forskningsfinansiär
KK-stiftelsen, 20160022
Anmärkning

Available online 9 November 2018

Tillgänglig från: 2018-12-03 Skapad: 2018-12-03 Senast uppdaterad: 2019-06-11Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Gupta, Mohit KumarMarkocsan, Nicolaie

Sök vidare i DiVA

Av författaren/redaktören
Gupta, Mohit KumarMarkocsan, Nicolaie
Av organisationen
Avdelningen för avverkande och additativa tillverkningsprocesser (AAT)
I samma tidskrift
Surface & Coatings Technology
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 47 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf