Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Experimental and PFEM-simulations of residual stresses from turning tests of a cylindrical Ti-6Al-4V shaft
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för avverkande och additativa tillverkningsprocesser (AAT). Swerea IVF AB, Argongatan 30, Mölndal SE-431 53, Sweden. (PTW)ORCID-id: 0000-0003-2991-2911
Luleå University of Technology, Division of Mechanics of Solid Materials Department of Engineering Sciences and Mathematics. Luleå SE-971 87, Sweden.
Swerea IVF AB, Argongatan 30, Mölndal SE-431 53, Sweden.
Luleå University of Technology, Division of Mechanics of Solid Materials Department of Engineering Sciences and Mathematics. Luleå SE-971 87, Sweden.
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Procedia CIRP, ISSN 2212-8271, E-ISSN 2212-8271, Vol. 71, s. 144-149Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Alloy Ti-6Al-4V is a frequently used material in aero space applications due the high strength and low weight. This material is however often considered as a difficult to machine alloy due to several material properties such as the inherent characteristics of high hot hardness and strength which is causing an increased deformation of the cutting tool during machining. The thermal properties also cause a low thermal diffusion from locally high temperatures in the cutting zone that allows for reaction to the tool material resulting in increased tool wear. Predicting the behavior of machining of this alloy is therefore essential when selecting machining tools or machining strategies. If the surface integrity is predicted, the influence of different machining parameters could be studied using Particle Finite Element (PFEM)-simulations. In this investigation the influence from cutting speed and feed during turning on the residual stresses has been measured using x-ray diffraction and compared to PFEM-simulations. The results showed that cutting speed and feed have great impact on the residual stress state. The measured cutting force showed a strong correlation especially to the cutting feed. The microstructure, observed in SEM, showed highly deformed grains at the surface from the impact of the turning operation and the full width half maximum from the XDR measurements distinguish a clear impact from different cutting speed and feed which differed most for the higher feed rate. The experimental measurements of the residual stresses and the PFEM simulations did however not correlate. The surface stresses as well as the sign of the residuals stresses differed which might be due to the material model used and the assumption of using a Coulomb friction model that might not represent the cutting conditions in the investigated case.

Ort, förlag, år, upplaga, sidor
2018. Vol. 71, s. 144-149
Nyckelord [en]
Ti-6Al-4V, X-ray diffraction, PFEM
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
TEKNIK, Produktions- och materialteknik; Produktionsteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-12477DOI: 10.1016/j.procir.2018.05.087Scopus ID: 2-s2.0-85051265926OAI: oai:DiVA.org:hv-12477DiVA, id: diva2:1218568
Konferens
4th CIRP Conference on Surface Integrity (CSI 2018)
Forskningsfinansiär
Vinnova, 2014-00919
Anmärkning

Available online 6 June 2018.

Tillgänglig från: 2018-06-14 Skapad: 2018-06-14 Senast uppdaterad: 2021-02-03Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Person

Holmberg, Jonas

Sök vidare i DiVA

Av författaren/redaktören
Holmberg, Jonas
Av organisationen
Avdelningen för avverkande och additativa tillverkningsprocesser (AAT)
I samma tidskrift
Procedia CIRP
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 193 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf