Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Multi-Robot Motion Planning Optimisation for Handling Sheet Metal Parts
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för produktionssystem (PS). (PTW)ORCID-id: 0000-0002-0044-2795
2017 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Motion planning for robot operations is concerned with path planning and trajectory generation. In multi-robot systems, i.e. with multiple robots operating simultaneously in a shared workspace, the motion planning also needs to coordinate the robots' motions to avoid collisions between them. The multi-robot coordination decides the cycle-time for the planned paths and trajectories since it determines to which extend the operations can take place simultaneously without colliding. To obtain the quickest cycle-time, there needs to bean optimal balance between, on the one hand short paths and fast trajectories, and on the other hand possibly longer paths and slower trajectories to allow that the operations take place simultaneously in the shared workspace. Due to the inter-dependencies, it becomes necessary to consider the path planning, trajectory generation and multi-robot coordination together as one optimisation problem in order to find this optimal balance.This thesis focusses on optimising the motion planning for multi-robot material handling systems of sheet metal parts. A methodology to model the relevant aspects of this motion planning problem together as one multi-disciplinary optimisation problem for Simulation based Optimisation (SBO) is proposed. The identified relevant aspects include path planning,trajectory generation, multi-robot coordination, collision-avoidance, motion smoothness, end-effectors' holding force, cycle-time, robot wear, energy efficiency, part deformations, induced stresses in the part, and end-effectors' design. The cycle-time is not always the (only) objective since it is sometimes equally/more important to minimise robot wear, energy consumption, and/or part deformations. Different scenarios for these other objectives are therefore also investigated. Specialised single- and multi-objective algorithms are proposed for optimising the motion planning of these multi-robot systems. This thesis also investigates how to optimise the velocity and acceleration profiles of the coordinated trajectories for multi-robot material handling of sheet metal parts. Another modelling methodology is proposed that is based on a novel mathematical model that parametrises the velocity and acceleration profiles of the trajectories, while including the relevant aspects of the motion planning problem excluding the path planning since the paths are now predefined.This enables generating optimised trajectories that have tailored velocity and acceleration profiles for the specific material handling operations in order to minimise the cycle-time,energy consumption, or deformations of the handled parts.The proposed methodologies are evaluated in different scenarios. This is done for real world industrial case studies that consider the multi-robot material handling of a multi-stage tandem sheet metal press line, which is used in the automotive industry to produce the cars' body panels. The optimisation results show that significant improvements can be obtained compared to the current industrial practice.

Ort, förlag, år, upplaga, sidor
Trollhättan: University West , 2017. , s. 196
Serie
PhD Thesis: University West ; 10
Nyckelord [en]
Multi-robot systems, motion planning, modelling and simulation, optimisation
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Forskningsämne
Produktionsteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-10947ISBN: 978-91-87531-58-3 (tryckt)ISBN: 978-91-87531-57-6 (tryckt)OAI: oai:DiVA.org:hv-10947DiVA, id: diva2:1098575
Handledare
Tillgänglig från: 2017-05-24 Skapad: 2017-05-24 Senast uppdaterad: 2017-05-30Bibliografiskt granskad
Delarbeten
1. Constructive cooperative coevolutionary optimisation for interacting production stations
Öppna denna publikation i ny flik eller fönster >>Constructive cooperative coevolutionary optimisation for interacting production stations
2015 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 78, nr 1-4, s. 673-688Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Optimisation of the control function for multiple automated interacting production stations is a complex problem, even for skilled and experienced operators or process planners. When using mathematical optimisation techniques, it often becomes necessary to use simulation models to represent the problem because of the high complexity (i.e. simulation-based optimisation). Standard optimisation techniques are likely to either exceed the practical time frame or under-perform compared to the manual tuning by the operators or process planners. This paper presents the Constructive cooperative coevolutionary (C3) algorithm, which objective is to enable effective simulation-based optimisation for the control of automated interacting production stations within a practical time frame. C3 is inspired by an existing cooperative coevolutionary algorithm. Thereby, it embeds an algorithm that optimises subproblems separately. C3 also incorporates a novel constructive heuristic to find good initial solutions and thereby expedite the optimisation. In this work, two industrial optimisation problems, involving interaction production stations, with different sizes are used to evaluate C3. The results illustrate that with C3, it is possible to optimise these problems within a practical time frame and obtain a better solution compared to manual tuning.

Nyckelord
Manufacturing automation, metaheuristic optimisation algorithm, optimised production technology, interacting production stations, sheet metal press line
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Forskningsämne
TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-7586 (URN)10.1007/s00170-015-7012-7 (DOI)000359835000055 ()2-s2.0-84939260196 (Scopus ID)
Anmärkning

Published online 2 April 2015

Tillgänglig från: 2015-05-07 Skapad: 2015-05-07 Senast uppdaterad: 2019-05-14Bibliografiskt granskad
2. Multi-objective constructive cooperative coevolutionary optimization of robotic press-line tending
Öppna denna publikation i ny flik eller fönster >>Multi-objective constructive cooperative coevolutionary optimization of robotic press-line tending
2017 (Engelska)Ingår i: Engineering optimization (Print), ISSN 0305-215X, E-ISSN 1029-0273, Vol. 49, nr 10, s. 1685-1703Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

This article investigates multi-objective optimization of the robot trajectories and position-based operation-coordination of complex multi-robot systems, such as press lines, to improve the production rate and obtaining smooth motions to avoid excessive wear of the robots’ components. Different functions for handling the multiple objectives are evaluated on realworld press lines, including both scalarizing single-objective functions and Pareto-based multi-objective functions. Additionally, the Multi-Objective Constructive Cooperative Coevolutionary (moC3) algorithm is proposed, for Pareto-based optimization, which uses a novel constructive initialization of the subpopulations in a co-adaptive fashion. It was found that Paretobased optimization performs better than the scalarizing single-objective functions. Furthermore, moC3 gives substantially better results compared to manual online tuning, as currently used in the industry. Optimizing robot trajectories and operation-coordination of complex multi-robot systems using the proposed method with moC3 significantly improves productivity and reduces maintenance. This article hereby addresses the lack of systematic methods for effectively improving the productivity of press lines.

Nyckelord
Multi-objective optimization, coevolutionary optimization, press tending, multi-robot coordination
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi Robotteknik och automation
Forskningsämne
TEKNIK, Produktions- och materialteknik; Produktionsteknik
Identifikatorer
urn:nbn:se:hv:diva-10341 (URN)10.1080/0305215X.2016.1264220 (DOI)000408952800003 ()2-s2.0-85006124128 (Scopus ID)
Anmärkning

Kolla upp ScopusID

Tillgänglig från: 2016-12-19 Skapad: 2016-12-19 Senast uppdaterad: 2019-05-23Bibliografiskt granskad
3. An energy model for press line tending robots
Öppna denna publikation i ny flik eller fönster >>An energy model for press line tending robots
2016 (Engelska)Ingår i: ESM'2016, the 2016 European simulation and Modelling Conference: Modelling and Simulation '2016 / [ed] José Evora-Gomez & José Juan Hernandez-Cabrera, Eurosis , 2016, s. 377-383Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Today most industries aim at reducing energy consumption to become sustainable and environment-friendly. The automotive industry, with mass production and large volumes, is one such example. With many robots working round the clock, there is great potential to save energy. In this climate there is a need for robot simulation models that can be used for motion and task execution optimisation and which are aimed lowering energy consumption. This paper presents an energy consumption model for 2D-belt robots for press line tending in the automotive sector. The energy model is generic for 2D-belt robots and is entirely based on component specifications (e.g., dimensions, masses, inertia). An implementation and validation against a real 2D-belt tending robot used in the automotive industry is performed and presented. The purpose and usefulness of the energy model is also demonstrated by two application cases; the investigation of potential energy reductions achieved by reducing the weight of gripper tools, and by using mechanical brakes when the robot is idle.

Ort, förlag, år, upplaga, sidor
Eurosis, 2016
Nyckelord
Industrial robots, energy model, energy consumption, energy minimisation
Nationell ämneskategori
Robotteknik och automation
Forskningsämne
Produktionsteknik; TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-10133 (URN)2-s2.0-85016052034 (Scopus ID)9789077381953 (ISBN)
Konferens
30th European Simulation and Modelling Conference - ESM'2016, October 26-28, 2016, Las Palmas, Gran Canaria, Spain
Anmärkning

This work was performed at University West’s Production Technology West research centre and supported in part by Västra Götalandsregionen under the grant PROSAM+ RUN 612-0208-16.

Tillgänglig från: 2016-11-10 Skapad: 2016-11-10 Senast uppdaterad: 2019-02-07Bibliografiskt granskad

Open Access i DiVA

fulltext(16494 kB)194 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 16494 kBChecksumma SHA-512
d30df7e7d8e1990949112ba48ad4196da96d2b0ce5ff7c786de29d4deca88204859416badae1b2a357e2375cc71e3158f0d6e4cc3b26c02a8f47d1604893f16c
Typ fulltextMimetyp application/pdf

Personposter BETA

Glorieux, Emile

Sök vidare i DiVA

Av författaren/redaktören
Glorieux, Emile
Av organisationen
Avdelningen för produktionssystem (PS)
Produktionsteknik, arbetsvetenskap och ergonomi

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 194 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 973 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf