Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Simulering av GMAW svetsprocessen med hjälp av ANSYS
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avd för tillverkningsprocesser.
2014 (svensk)Independent thesis Advanced level (degree of Master (One Year)), 20 poäng / 30 hpOppgaveAlternativ tittel
Simulation of GMAW welding process in L-shape joint using ANSYS (engelsk)
Abstract [en]

In present research, a three dimensional welding process phenomenon is simulated using a commercial finite element package ANSYS® in order to study the heat distribution and residual stress in SAE 1020 fillet joint.

Heat distribution in different points of weldment shows that peak temperature at the nods near weld line is higher than peak temperature at nods which are located further. Also, temperature shapely increases when it subject to heat input and then falls down with a relatively lower rate after peak temperature.

Longitudinal residual stress which is most important stress field in the specimen, in HAZ region and near the weld line is tensile with maximum values but with increase of distance from weld line the stresses decrease. Contractual resistance of material at the beginning of cooling process is a reason for generating the tensile stress.

Transverse residual stresses perpendicular to the weld line, at the beginning and end of fillet joint is compressive due to constraints and changes to tensile in the middle of weld line. Maximum transverse residual stress will be happened at the middle and by increasing the distance the stress values approach to zero. Although, transverse residual stress values are lower than longitudinal residual stress but those should be considered as a main factor in weld deign.

As a matter of fact, in present research maximum longitude stress (100 MPa) and transverse stress (30 MPa) satisfy AWS D1.1 weld design code requirements. According to Structural Welding Code-Steel, AWS D1.1, tension or compression parallel to axis of weld shouldn't exceed base metal tensile strength i.e 420 MPa for SAE 1020. Further, shear on effective area should be less than 0.3 of nominal tensile strength of filler material i.e 126 MPa

sted, utgiver, år, opplag, sider
2014. , s. 73
Emneord [en]
Thermal analysis, Temperature-dependent material properties, Temperature distribution, Welding simulation, FEM, Residual stresses
HSV kategori
Identifikatorer
URN: urn:nbn:se:hv:diva-6868Lokal ID: EXD904OAI: oai:DiVA.org:hv-6868DiVA, id: diva2:756538
Fag / kurs
Mechanical engineering
Veileder
Examiner
Tilgjengelig fra: 2014-10-20 Laget: 2014-10-17 Sist oppdatert: 2014-10-20bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 292 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf