Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Tool Wear Geometry Updating in Inconel 718 Turning Simulations.
Högskolan Väst, Institutionen för teknik, matematik och datavetenskap, Avd för maskinteknik.
Högskolan Väst, Institutionen för teknik, matematik och datavetenskap, Avd för maskinteknik.
2006 (engelsk)Inngår i: 9th CIRP International Workshop on Modelling of Machining Operation: Bled, Slovenia, 2006, s. 491-498Konferansepaper, Publicerat paper (Annet vitenskapelig)
Abstract [en]

In machining of nickel based superalloys, such as Inconel 718, tool wear is a major problem due to the high stresses and the high temperatures at the tool chip interface. Enhanced knowledge of the tool wear mechanism and capability to predict tool wear are therefore of great importance in machining of nickel based superalloys. The objective with this paper is to investigate if the finite element method (FEM) can be used to predict the flank and crater wear of uncoated cemented carbide tool in turning ofInconel 718. An empirical model has been implemented in a commercial FE-code and the tool geometry is continuously updated to capture the evolution of wear. Experiments have been conducted to obtain parameters for the empirical wear model and for validation of the simulations. The worn geometry at the flank and rake face as well as the cutting edge radius was measured with white light interferometry. Wear model parameters were calibrated by fitting a simulation against measured worn geometries at the flank and rake face. Then separate simulations at other cutting speeds were compared with corresponding experiments to validate the model performance.

sted, utgiver, år, opplag, sider
2006. s. 491-498
HSV kategori
Forskningsprogram
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-1909OAI: oai:DiVA.org:hv-1909DiVA, id: diva2:275521
Konferanse
9th CIRP International Workshop on Modelling of Machining Operation, Bled, Slovenia
Tilgjengelig fra: 2009-11-05 Laget: 2009-11-05 Sist oppdatert: 2019-11-19bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

http://www.fs.uni-lj.si/lasin/cirp9ws06/abstracts/Lorentzon.pdf

Søk i DiVA

Av forfatter/redaktør
Lorentzon, JohnJärvstråt, Niklas
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 531 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf