Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Monitoring and control of laser beam butt joint welding
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för produktionssystem (PS). (PTW)ORCID-id: 0000-0002-8771-7404
2019 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Laser beam welding is one important technology in automated production. It has several advantages, such as the ability to produce deep and narrow welds giving limited heat induced deformations. The laser beam welding process is however sensitive to how the high power laser is positioned with regards to the joint position. Therefore, to achieve a seam without defects, the joint position needs to be measured and controlled. The laser beam welding process is also sensitive to variations in joint gap width. Costly joint preparations are required to achieve the tight fit up tolerances needed to produce high quality welds. However, the demand on joint preparation can be somewhat relaxed by allowing the joint gap width to vary and controlling the process. One way of doing this is to control the filler wire feed rate based on joint gap width measurements.This thesis presents experimental studies on how to track closed-square-butt joints and also how to handle varying square-butt joints in laser beam welding.

Different optical sensor systems are evaluated for their performance to estimate the joint position and the joint gap width. The possibility of detecting beam offsets is studied by using sensors systems based on a photo diode and on a spectrometer. Estimations of the joint position, to be used for closed loop position control, is studied by using a camera and external LED illumination. Variations in joint gap width is evaluated using a spectrometer, a camera and a laser profile sensor. Experimental results show that both the photodiode system and the spectometer system is able to detect beam offsets and that the beam position can be estimated with sufficient accuracy when welding closed-square-butt joints. It is also shown that the joint gap width can be estimated by the selected sensor systems and that the estimates can be used for controlling the wire feed rate in order to obtain a constant weld geometry and avoid defects related to the gap width.

sted, utgiver, år, opplag, sider
Trollhättan: University West , 2019. , s. 84
Serie
PhD Thesis: University West ; 27
Emneord [en]
Laser beam welding, Optical sensors, Joint tracking, Varying gap
HSV kategori
Forskningsprogram
Produktionsteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-13650ISBN: 978-91-88847-23-2 (tryckt)ISBN: 978-91-88847-22-5 (digital)OAI: oai:DiVA.org:hv-13650DiVA, id: diva2:1292567
Disputas
2019-02-05, F104, Albertsalen, Trollhättan, 10:15 (engelsk)
Opponent
Veileder
Tilgjengelig fra: 2019-03-15 Laget: 2019-02-28
Delarbeid
1. Optical Methods for In-Process Monitoring of Laser Beam Welding
Åpne denne publikasjonen i ny fane eller vindu >>Optical Methods for In-Process Monitoring of Laser Beam Welding
2014 (engelsk)Inngår i: Proceedings of the 6th International Swedish Production Symposium 2014 / [ed] Stahre, Johan, Johansson, Björn & Björkman, Mats, 2014, s. 1-9Konferansepaper, Publicerat paper (Fagfellevurdert)
Abstract [en]

This paper addresses the issue of evaluating and selecting optical sensors to be integrated with a 1μm laser beam welding system. The method used for this evaluation is mainly a survey of relevant research litterature. The result of this work is a matrix showing the different methods and distinct features related to relevant process conditions that can be estimated or detected with respective methods. This evaluation also includes considerations on the required sensor bandwidth in relation to inertia and time constants in the physical process.

Emneord
Optical methods, process monitoring, laser beam welding
HSV kategori
Forskningsprogram
TEKNIK, Mekatronik; Produktionsteknik
Identifikatorer
urn:nbn:se:hv:diva-6854 (URN)978-91-980974-1-2 (ISBN)
Konferanse
The 6th Swedish Production Symposium
Tilgjengelig fra: 2014-10-15 Laget: 2014-10-15 Sist oppdatert: 2019-02-28bibliografisk kontrollert
2. Detecting beam offsets in laser welding of closed-square-butt joints by wavelet analysis of an optical process signal
Åpne denne publikasjonen i ny fane eller vindu >>Detecting beam offsets in laser welding of closed-square-butt joints by wavelet analysis of an optical process signal
Vise andre…
2019 (engelsk)Inngår i: Optics and Laser Technology, ISSN 0030-3992, E-ISSN 1879-2545, Vol. 109, s. 178-185Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Robotized laser beam welding of closed-square-butt joints is sensitive to the positioning of the laser beam with respect to the joint since even a small offset may result in a detrimental lack of sidewall fusion. An evaluation of a system using a photodiode aligned coaxial to the processing laser beam confirms the ability to detect variations of the process conditions, such as when there is an evolution of an offset between the laser beam and the joint. Welding with different robot trajectories and with the processing laser operating in both continuous and pulsed mode provided data for this evaluation. The detection method uses wavelet analysis of the photodetector signal that carries information of the process condition revealed by the plasma plume optical emissions during welding. This experimental data have been evaluated offline. The results show the potential of this detection method that is clearly beneficial for the development of a system for welding joint tracking.

sted, utgiver, år, opplag, sider
Elsevier, 2019
Emneord
Laser beam welding, Joint tracking, Butt joints, Photodiode, Wavelet analysis
HSV kategori
Forskningsprogram
Produktionsteknik
Identifikatorer
urn:nbn:se:hv:diva-12832 (URN)10.1016/j.optlastec.2018.08.006 (DOI)000446949600023 ()2-s2.0-85051138319 (Scopus ID)
Forskningsfinansiär
VINNOVA, 2016-03291
Tilgjengelig fra: 2018-08-21 Laget: 2018-08-21 Sist oppdatert: 2019-02-28bibliografisk kontrollert
3. Vision and spectroscopic sensing for joint tracing in narrow gap laser butt welding
Åpne denne publikasjonen i ny fane eller vindu >>Vision and spectroscopic sensing for joint tracing in narrow gap laser butt welding
2017 (engelsk)Inngår i: Optics and Laser Technology, ISSN 0030-3992, E-ISSN 1879-2545, Vol. 96, s. 107-116Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The automated laser beam butt welding process is sensitive to positioning the laser beam with respect to the joint because a small offset may result in detrimental lack of sidewall fusion. This problem is even more pronounced incase of narrow gap butt welding, where most of the commercial automatic joint tracing system fail to detect the exact position and size of the gap. In this work, adual vision and spectroscopic sensing approach is proposed to trace narrow gap butt joints during laser welding. The system consists of a camera with suitable illumination and matched optical filters and a fast miniature spectrometer. An image processing algorithm of the camera recordings has been developed in order to estimate the laser spot position relative the joint position. The spectral emissions from the laser induced plasma plume has been acquired by the spectrometer, and based on the measurements of the intensities of selected lines of the spectrum, the electron temperature signal has been calculated and correlated to variations of process conditions. The individual performances of these two systems have been experimentally investigated and evaluated offline by data from several welding experiments where artificial abrupt as well as gradual excursions of the laser beam out of the joint were produced. Results indicate thata combination of the information provided by the vision and spectroscopic systems is beneficial for development of a hybrid sensing system for joint tracing.

Emneord
Laser beam welding, Joint tracing, Butt joints, Optical spectroscopy, Vision sensor, Hybrid sensing
HSV kategori
Forskningsprogram
Produktionsteknik; TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-10639 (URN)10.1016/j.optlastec.2017.05.011 (DOI)000405051800015 ()2-s2.0-85019735734 (Scopus ID)
Forskningsfinansiär
Vinnova, 2014-05227Knowledge Foundation, 2010/0283EU, FP7, Seventh Framework Programme, FP7/2007-2013
Merknad

Ingår i lic. avhandling

Tilgjengelig fra: 2017-02-03 Laget: 2017-02-03 Sist oppdatert: 2019-05-23bibliografisk kontrollert
4. Robust vision-based joint tracking for laser welding of curved closed-square-butt joints
Åpne denne publikasjonen i ny fane eller vindu >>Robust vision-based joint tracking for laser welding of curved closed-square-butt joints
2019 (engelsk)Inngår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 101, nr 5-8, s. 1867-1978Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Robotized laser beam welding of closed-square-butt joints is sensitive to how the focused laser beam is positioned in relation to the joint, and existing joint tracking systems tend to fail in detecting the joint when the gap and misalignment between the work pieces are close to zero. A camera-based system is presented based on a high dynamic range camera operating with LED illumination at a specific wavelength and a matching optical filter. An image processing algorithm based on the Hough transform extracts the joint position from the camera images, and the joint position is then estimated using a Kalman filter. The filter handles situations, when the joint is not detectable in the image, e.g., when tack welds cover the joint. Surface scratches, which can be misinterpreted as being the joint, are handled by a joint curve prediction model based on known information about the nominal path defined by the robot program. The performance of the proposed system has been evaluated off line with image data obtained during several welding experiments.

Emneord
Laser beam welding, Joint tracking, Butt joints, Camera, Hough transform, Kalman filter
HSV kategori
Forskningsprogram
TEKNIK, Produktions- och materialteknik
Identifikatorer
urn:nbn:se:hv:diva-13211 (URN)10.1007/s00170-018-3044-0 (DOI)
Prosjekter
VINNOVA project VarGa
Forskningsfinansiär
Vinnova, 2016-03291
Merknad

First Online: 27 November 2018

Funders: SWE-DEMO MOTOR ; [2015-06047]

Tilgjengelig fra: 2018-12-18 Laget: 2018-12-18 Sist oppdatert: 2019-05-10bibliografisk kontrollert
5. Monitoring of Varying Joint Gap Width During Laser Beam Welding by a Dual Vision and Spectroscopic Sensing System
Åpne denne publikasjonen i ny fane eller vindu >>Monitoring of Varying Joint Gap Width During Laser Beam Welding by a Dual Vision and Spectroscopic Sensing System
2017 (engelsk)Inngår i: Physics Procedia, ISSN 1875-3892, E-ISSN 1875-3892, Vol. 89, s. 100-107Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A vision and spectroscopic system for estimation of the joint gap width in autogenous laser beam butt welding is presented. Variations in joint gap width can introduce imperfections in the butt joint seam, which in turn influence fatigue life and structural integrity. The aim of the monitoring approach explored here is to acquire sufficiently robust process data to be used to guide post inspection activities and/or to enable feedback control for a decreased process variability. The dual-sensing approach includes a calibrated CMOS camera and a miniature spectrometer integrated with a laser beam tool. The camera system includes LED illumination and matching optical filters and captures images of the area in front of the melt pool in order to estimate the joint gap width from the information in the image. The intensity of different spectral lines acquired by the spectrometer has been investigated and the correlation between the intensity of representative lines and the joint gap width has been studied. Welding experiments have been conducted using a 6 kW fiber laser. Results from both systems are promising, the camera system is able to give good estimations of the joint gap width, and good correlations between the signal from the spectrometer and the joint gap width have been found. However, developments of the camera setup and vision algorithm can further improve the joint gap estimations and more experimental work is needed in order to evaluate the robustness of the systems.

Emneord
Laser beam welding; Butt joints; Varying gap width; Vision sensor; Spectroscopic sensor
HSV kategori
Forskningsprogram
Produktionsteknik
Identifikatorer
urn:nbn:se:hv:diva-11898 (URN)10.1016/j.phpro.2017.08.014 (DOI)2-s2.0-85037711817 (Scopus ID)
Konferanse
16th Nordic Laser Materials Processing Conference, NOLAMP16
Forskningsfinansiär
Vinnova, 2016-03291
Merknad

Funders: People programme (Marie Curie Actions) of the European Union's 29 seventh framework progamme (FP7/2007-2013), no 608473

Tilgjengelig fra: 2017-12-11 Laget: 2017-12-11 Sist oppdatert: 2019-05-21bibliografisk kontrollert
6. Adaptive control of the filler wire rate during laser beam welding of squared butt joints with varying gap width
Åpne denne publikasjonen i ny fane eller vindu >>Adaptive control of the filler wire rate during laser beam welding of squared butt joints with varying gap width
2019 (engelsk)Inngår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, s. 1-10Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Adding filler wire control to autogenous laser beam welding of squared butt joints offers a means to widen up the tight fit-up tolerances associated with this process. When the gap width varies, the filler wire rate should be controlled to assure a constant geometry of the resulting weld seam. A dual mode sensing system is proposed to estimate the joint gap width and thereby control the filler wire rate. A vision camera integrated into the welding tool together with external LED illumination and a laser line projection enables two sensing modes, one surface feature extraction mode and one laser triangulation-based mode. Data from the both modes are fused in a Kalman filter, and comparisons show that the fusing of the data gives more robust estimation than estimates from each single mode. A feed-forward control system adaptively adjusts the filler wire rate based on the estimations ofthe joint gap width in front of the keyhole. The focus is on keeping the data processing simple and affordable, and the real-time performance of the sensor and control system has been evaluated by welding experiments. It is shown that the proposed system can be used for on-line control of the filler wire rate to achieve a constant weld geometry during varying joint gap widths

sted, utgiver, år, opplag, sider
Springer, 2019
Emneord
Laser beam welding, Filler wire, Squared butt joints, Varying gap width, Feature extraction, Laser triangulation, Sensor fusion
HSV kategori
Forskningsprogram
Produktionsteknik
Identifikatorer
urn:nbn:se:hv:diva-13640 (URN)10.1007/s00170-019-03325-w (DOI)
Tilgjengelig fra: 2019-02-28 Laget: 2019-02-28 Sist oppdatert: 2019-03-06bibliografisk kontrollert

Open Access i DiVA

fulltext(9526 kB)42 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 9526 kBChecksum SHA-512
7aa1e0e6359d6e685e914792709bb0d9f3d9355124115683a6910520b6875b470bcd34aef0fb9f2a4eb58dd384a33f46dbaae0d7da35e008db18514e75fe338b
Type fulltextMimetype application/pdf

Personposter BETA

Nilsen, Morgan

Søk i DiVA

Av forfatter/redaktør
Nilsen, Morgan
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 42 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

isbn
urn-nbn

Altmetric

isbn
urn-nbn
Totalt: 119 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf