Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Residual stresses and distortions in austenitic stainless steel 316L specimens manufactured by Selective Laser Melting
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för svetsteknologi (SV).
2018 (engelsk)Independent thesis Advanced level (degree of Master (One Year)), 10 poäng / 15 hpOppgave
Abstract [en]

Residual stresses are one of the major challenges in additive manufacturing of metallic materials today. They are induced during manufacturing because of the rapid local heating and cooling and may cause distortions, cracking and delamination between layers. The magnitude of the residual stresses depends on factors such as manufacturing technology, material, part geometry, scanning strategy, process parameters, preheating temperature and density of the component. In the present work, the magnitudes of residual stresses and distortions in austenitic stainless steel 316L components manufactured by Selective Laser melting have been investigated. Four specimens with rectangular cross-sections where produced with different heights and wall thicknesses. The residual stresses were measured by two different methods, x-ray diffraction and Electronic Speckle Pattern Interferometry (ESPI) incremental hole drilling in order to see how well they correspond to each other. The results showed peaks of high tensile stresses in the building direction in all specimens. The magnitudes of stresses were similar in all four specimens. The largest distortions occurred when the wall thickness was increased, and the height was reduced. It was also shown that the measurements made by x-ray diffraction and ESPI incremental hole drilling were not consistent with each other. The latter showed unrealistically high measurements near the surface.

sted, utgiver, år, opplag, sider
2018. , s. 49
Emneord [en]
Residual Stresses, Distortions, SLM, Selective Laser Melting, 316L, X-ray diffraction, XRD, ESPI, Hole drilling
HSV kategori
Identifikatorer
URN: urn:nbn:se:hv:diva-12771Lokal ID: EXP800OAI: oai:DiVA.org:hv-12771DiVA, id: diva2:1232298
Fag / kurs
Mechanical engineering
Utdanningsprogram
Produktionsteknik
Veileder
Examiner
Tilgjengelig fra: 2018-07-26 Laget: 2018-07-11 Sist oppdatert: 2018-07-26bibliografisk kontrollert

Open Access i DiVA

fulltext(2029 kB)77 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 2029 kBChecksum SHA-512
0614c7e6c0f396815b1a4e039ecef50383725af9bb486ff25de0252690a7da9e71d9de32dc55dc274fc6c60457685b3cd83b024b55c88f4822d48e885d56d308
Type fulltextMimetype application/pdf

Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 77 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 211 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf