Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructure and Porosity of Laser Welds in Cast Ti-6Al-4V with Addition of Boron
Chalmers University of Technology, Department of Industrial and Materials Science, Gothenburg, Sweden.
Högskolan Väst, Institutionen för ingenjörsvetenskap, Avdelningen för svetsteknologi (SV). Chalmers University of Technology, Department of Industrial and Materials Science, Gothenburg, Sweden. (PTW)ORCID-id: 0000-0002-7675-7152
Chalmers University of Technology, Department of Industrial and Materials Science, Gothenburg, Sweden.
2018 (engelsk)Inngår i: Metallurgical and Materials Transactions. A, ISSN 1073-5623, E-ISSN 1543-1940, Vol. 49A, nr 5, s. 1683-1691Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Addition of small amounts of boron to cast Ti-6Al-4V alloy has shown to render a finer microstructure and improved mechanical properties. For such an improved alloy to be widely applicable for large aerospace structural components, successful welding of such castings is essential. In the present work, the microstructure and porosity of laser welds in a standard grade cast Ti-6Al-4V alloy as well as two modified alloy versions with different boron concentrations have been investigated. Prior-β grain reconstruction revealed the prior-β grain structure in the weld zones. In fusion zones of the welds, boron was found to refine the grain size significantly and rendered narrow elongated grains. TiB particles in the prior-β grain boundaries in the cast base material restricted grain growth in the heat-affected zone. The TiB particles that existed in the as cast alloys decreased in size in the fusion zones of welds. The hardness in the weld zones was higher than in the base material and boron did not have a significant effect on hardness of the weld zones. The fusion zones were smaller in the boron-modified alloys as compared with Ti-6Al-4V without boron. Computed tomography X-ray investigations of the laser welds showed that pores in the FZ of the boron modified alloys were confined to the lower part of the welds, suggesting that boron addition influences melt pool flow. © 2018 The Author(s)

sted, utgiver, år, opplag, sider
2018. Vol. 49A, nr 5, s. 1683-1691
HSV kategori
Forskningsprogram
TEKNIK, Produktions- och materialteknik
Identifikatorer
URN: urn:nbn:se:hv:diva-12232DOI: 10.1007/s11661-018-4543-1ISI: 000428844800029Scopus ID: 2-s2.0-85043478044OAI: oai:DiVA.org:hv-12232DiVA, id: diva2:1194694
Merknad

Funders: NFFP (the Swedish National Program for Aeronautical Technology).

Tilgjengelig fra: 2018-04-03 Laget: 2018-04-03 Sist oppdatert: 2020-01-29bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Person

Pederson, Robert

Søk i DiVA

Av forfatter/redaktør
Pederson, Robert
Av organisasjonen
I samme tidsskrift
Metallurgical and Materials Transactions. A

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 127 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf